Search:

Type: Posts; User: Betabass

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    1,644

    Maybe considering the startup issue should...

    Maybe considering the startup issue should consider replacing the orifice with the correct size.
  2. Replies
    10
    Views
    1,644

    Information taken from power flames website, I...

    Information taken from power flames website, I would check the air damper positioning....


    In order to prepare the pilot for proper operation, it is essential that appropriate adjustments be made...
  3. Hand deliver a reasonable quote to replace the...

    Hand deliver a reasonable quote to replace the plate, customers are hard to get. You
    can't afford the negative publicity if you simply walk away.
  4. Replies
    19
    Views
    1,476

    Are you also heating the pool water?

    Are you also heating the pool water?
  5. Replies
    34
    Views
    1,771

    Please disregard my previous post, me...

    Please disregard my previous post, me bad.........

    Beta,
  6. Replies
    34
    Views
    1,771

    Please ask any question you have in the...

    Please ask any question you have in the appropriate forum, are you looking for support in residential or commercial Hvac service? There is a truck load of knowledge on this website.
    Just have to...
  7. Mcquay Unit Ventilator model U.AZU.5.040.K.H.13.2.87.AL.22.G.N.B.1

    Greetings,

    Troubleshooting a Mcquay Unit Ventilator

    Stand alone control at unit no remote thermostat and not networked,

    Problem is the unit will not operate in the auto mode, there is a LUI...
  8. Replies
    33
    Views
    2,854

    I would consider if the 410A may have been...

    I would consider if the 410A may have been compromised with moisture or air, I would pull the charge replace the driers and and recharge with virgin 410a to name plate before I would consider...
  9. Thread: on call

    by Betabass
    Replies
    134
    Views
    11,888

    Looking at it from always on call no thanks, I...

    Looking at it from always on call no thanks, I rotate 1/2 week with 15 other techs.
  10. Thread: on call

    by Betabass
    Replies
    134
    Views
    11,888

    On Call = time and 1/2, double Time, paid from...

    On Call = time and 1/2, double Time, paid from the time I leave my house until I return Home.
    Don't enjoy it but It certainly has it's perks. Once you do it a while you get use to it.
  11. I agree with Gocolts however you may want to...

    I agree with Gocolts however you may want to verify your suction readings with another gauge if you haven't done so. The temps and pressure you indicate are a little strange. I am a summing the...
  12. Thread: heat pump

    by Betabass
    Replies
    5
    Views
    445

    Reversing valve may be in intermediate position...

    Reversing valve may be in intermediate position try powering valve with a jumper or removing power from valve a few times and see it it repositions.......
  13. Replies
    1
    Views
    535

    Interesting 1 degree Superheat 0 degree...

    Interesting
    1 degree Superheat 0 degree Subcooling
    Isolation valves wide open Check?
    Hopefully you removed all the rubber plugs in your ACR Copper Pipe?
    It happens, soundalike a major...
  14. Thread: heat pump

    by Betabass
    Replies
    5
    Views
    445

    More information will be needed, obvious...

    More information will be needed, obvious restrictions in discharge/liquid line somewhere,
    Where is the icing occurring? How long will the compressor cycle with the high pressure?
    What refrigerant...
  15. Replies
    16
    Views
    1,334

    If the single phase compressor is wired wrong it...

    If the single phase compressor is wired wrong it will not start. Depending how it was wired wrong it could burn the windings and there you go You have a dead compressor.
    You need to verify how the...
  16. Replies
    44
    Views
    2,642

    Wonder how the tech charged the system who...

    Wonder how the tech charged the system who installed the filter dryer, (No Access Port)
  17. Replies
    9
    Views
    892

    Agree

    Agree
  18. Replies
    1
    Views
    352

    Worn out or bad bonnet seal.

    Worn out or bad bonnet seal.
  19. Replies
    10
    Views
    1,101

    Some joints are in a very bad location you have...

    Some joints are in a very bad location you have to keep heating and filling Silfos until you are satisfied, pretty much what ever it takes.......
  20. I'm not an engineer but a dedicated system that...

    I'm not an engineer but a dedicated system that designed to provide a calculated air changes per minute may help this situation.......
  21. The Unloaders are designed to unload the...

    The Unloaders are designed to unload the compressors to maintain a desirable suction pressure, if you remove them you could create a liquid flood back situation while operating under low low load...
  22. Replies
    30
    Views
    1,803

    I'm not sure if you checked if service valves...

    I'm not sure if you checked if service valves were back seated I will assume you did and agree you have a defected compressor with no pressure diff and pulling amps.
  23. Replies
    9
    Views
    936

    I second........

    I second........
  24. Replies
    14
    Views
    1,226

    I had some issues with noisey condenser that sat...

    I had some issues with noisey condenser that sat on sleepers that we installed heavy duty vibration springs under the unit to lessen the sound issues. I am not sure if the AAon RTU Curb has options...
  25. Replies
    73
    Views
    5,751

    I agree why use a nitrogen purge for small...

    I agree why use a nitrogen purge for small repairs such as solenoids or TXV Installs, I concur with Grayline, I am an old timer however I am not aware of any young or old Techs following up on my...
Results 1 to 25 of 49
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event