Search:

Type: Posts; User: 11crv

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    359

    Picked up a ridgid micro ca100 camera i havent...

    Picked up a ridgid micro ca100 camera i havent used it in the field yet but it 225.00 from homedepot online. Johnston carries them aswell. The only review i can give so far is it looks good:grin2:
  2. For carrier I remove the burners if I can't get...

    For carrier I remove the burners if I can't get to the screw for the flame sensor. Wrap steel wool around the sensor and give it a couple runs cleans it up. Sometimes removing the burners if faster....
  3. Replies
    8
    Views
    327

    When i got here last night i noticed my dad had a...

    When i got here last night i noticed my dad had a dehum in the hallway. He said that is the only way he can control the humidity. I the last 3 hours the himidity has gone up 5%. Currently 49%. Ill...
  4. Replies
    8
    Views
    327

    2 adults, 2 bath fans used after showers. 22*...

    2 adults, 2 bath fans used after showers. 22* here this am house humidity 46%. IIRC they have always had moisture on the windows.
  5. Replies
    8
    Views
    327

    High humidity in dad's house

    Ranch 1400 sq/ft new double pane windows, well insulating home built in 1987. He lives in northern wisconsin has a skuttle type fresh air to the return. My dad says they have moisture on the windows...
  6. Replies
    6
    Views
    380

    I use an April aire with humidistat in the return...

    I use an April aire with humidistat in the return duct. No fireplace or wood stove. The condensation on windows might be from me Keeping a higher humidity level and leaky windows double pane windows.
  7. Replies
    6
    Views
    380

    I have two adults and a one year old. Windows...

    I have two adults and a one year old. Windows condense. I keep the humidity around 35%-45% depending on out side temp. I installed hardwood floor in the entire home. No bath fan. I dont really care...
  8. Replies
    6
    Views
    380

    Hrv or erv recommendations

    Im thinking of adding one of these to my home. 1300 sq/ft ranch built in the early 50's. I use an ultra-aire to dehumidify the basement now. It currently is not hooked to the duct work. I thought...
  9. Pressure switch closing? Shouldnt the ignitor use...

    Pressure switch closing? Shouldnt the ignitor use 120v?
  10. Replies
    18
    Views
    1,390

    Inspection camera

    What are you guys using in the field. I think having one would make heat exchanger inspection a lot easier. Sure would beat tearing open the plenum
  11. Replies
    4
    Views
    404

    Yup all the engineers i talked with say no lower...

    Yup all the engineers i talked with say no lower than 60*. You will have condensation issues
  12. Thread: Working in bars

    by 11crv
    Replies
    18
    Views
    1,067

    Long time ago when i first started i worked in a...

    Long time ago when i first started i worked in a strip club that had a lunch buffet. It was hilarious. They were cooling the place with 2 large window shakers.
  13. Thread: Working in bars

    by 11crv
    Replies
    18
    Views
    1,067

    Working in bars

    I hate working in bars when its happy hour or when rhey are busy. Its even worse when the mechanical room is on the way to the bathroom or outdoor smoking area. Just about every person on a barstool...
  14. Thread: New Veto MC

    by 11crv
    Replies
    119
    Views
    13,368

    Ordered mine today from a local supplier. They...

    Ordered mine today from a local supplier. They said the computer said instock must be in the ware house someplace?
  15. Replies
    32
    Views
    1,268

    The follow up.... Work purchased an iphone for me...

    The follow up.... Work purchased an iphone for me i asked for the 32gb iphone 5s. They also purchased the life proof nuud case and for added protection had a glass screen protector installed at the...
  16. Thread: New Veto MC

    by 11crv
    Replies
    119
    Views
    13,368

    Some websites say sept 12th. I think ill pick one...

    Some websites say sept 12th. I think ill pick one up.
  17. Replies
    30
    Views
    1,386

    Clean your evap be sure fan speeds are correct...

    Clean your evap be sure fan speeds are correct but sounds like noncondensables.
  18. Replies
    18
    Views
    1,662

    My favorite pulse is the one with an ecm. That...

    My favorite pulse is the one with an ecm. That thing is craaaaazzy!
  19. Replies
    18
    Views
    1,662

    We have a lot of pulses around here most of them...

    We have a lot of pulses around here most of them are about 20 yrs old. I think they are a decent furnace. Our customers get them checked every year and most of them check good. We also replace quite...
  20. Replies
    37
    Views
    2,581

    Making it magnetic would be nice

    Making it magnetic would be nice
  21. Replies
    10
    Views
    555

    Send the cdc to them. Why risk it bringing them...

    Send the cdc to them. Why risk it bringing them here?
  22. Replies
    32
    Views
    1,268

    So you can use a regular screen protector with...

    So you can use a regular screen protector with the nuud? I dont know why im asking you all these question the answer are out there somewhere. They, the verizon rep, showed me the nuud case but i...
  23. Replies
    32
    Views
    1,268

    How do you like the screen protector?

    How do you like the screen protector?
  24. Replies
    32
    Views
    1,268

    Lmao:cheers:

    Lmao:cheers:
  25. Replies
    32
    Views
    1,268

    Which life proof case do you have? Just got back...

    Which life proof case do you have? Just got back from verizon and i think i will get the 5s. In our house apple is everywhere and we have had zero issues from iphones, ipads, macs, apple tv. I looked...
  26. Replies
    32
    Views
    1,268

    Need a new phone what do you guys recommend?

    Our shop current uses droid phones, the razr m, my phone has been having issues for a while and our contract is up next week. The shop will provide a smart phone but if i want a specific one i have...
  27. Replies
    5
    Views
    454

    With the tool on the duct you should be rotating...

    With the tool on the duct you should be rotating clockwise with the drill tilted back alittle. Once the drill has been tilted you will it doesnt take much force to keep it rotating. Let the drill...
  28. Thread: Nylog??

    by 11crv
    Replies
    20
    Views
    1,195

    Same here, nylog valve caps. I also replace the...

    Same here, nylog valve caps. I also replace the plastic service caps with brass caps that have orings on PMs. I find alot of leaking valves
  29. Replies
    5
    Views
    688

    Digicools bar graph

    What is it there for?
  30. Replies
    29
    Views
    2,794

    If a furnace or air handler has water damage...

    If a furnace or air handler has water damage should it be replaced? Most insurance companies aroung here want the entire unit replaced if the water level submerges the board or wires.
  31. Thread: Unico system

    by 11crv
    Replies
    8
    Views
    522

    I was not in service today but the customer...

    I was not in service today but the customer called in a no cool today. It stopped working over night again. I am not sure what the other tech found today but i will post when i get the info from...
  32. Replies
    14
    Views
    918

    Some of our installers will keep it in but the...

    Some of our installers will keep it in but the other day i helped with an install that guy kept the bulb out. I asked wht because no one else does. He said always keep the bulb out. I also noticed...
  33. Replies
    14
    Views
    918

    Mounting txv bulb

    We install adp coils that have the sensing bulb mounted on the coil manifold in a horizontal position. Is it better to have the bulb mounted outside the plenum? From a service stand point it would be...
  34. Thread: Unico system

    by 11crv
    Replies
    8
    Views
    522

    There is a txv and i am wondering if something is...

    There is a txv and i am wondering if something is going on with it not closing enough. This all started when i replaced the bower motor for the fourth time for rusting and then not working. I was the...
  35. Thread: Unico system

    by 11crv
    Replies
    8
    Views
    522

    Unico system

    I have been having some issues with a unico system. According to tech support at unico this system was undercharged this is what i got...
    R22 rheem 1.5 ton straight cool
    Unico ah in the Attic with...
  36. Replies
    10
    Views
    549

    I didnt go back today, but got the full story...

    I didnt go back today, but got the full story from the other tech. The a/c was running along time without the cond. fan running. I thought that had something to do with the odd readings maybe oil to...
  37. Replies
    10
    Views
    549

    Is it possible for something to happen to the...

    Is it possible for something to happen to the piston if the cond fan motor is not running causing high head pressure?
  38. Replies
    10
    Views
    549

    No cool after tune up

    Another tech performed pm on a trane a/c. He went back due to broken wire terminal for cond fan motor on the capacitor. Then i get a call late last night from an unhappy customer. This is what i...
  39. How far in the fan shroud should the fan blades...

    How far in the fan shroud should the fan blades be?
  40. Thread: Going digital?

    by 11crv
    Replies
    51
    Views
    3,238

    I bought my first set of digital gauges this...

    I bought my first set of digital gauges this spring. Digicools. I love them most of the guys at work seems to like them. At least for me they really make you look how the entire system is working....
  41. Replies
    30
    Views
    1,982

    I had a contactor today where the contacts were...

    I had a contactor today where the contacts were pitted and it was black around the contacts. I recommended to the customer it should be replaced and showed her. She was hesitant at first because they...
  42. Replies
    7
    Views
    353

    I totally agree.

    I totally agree.
  43. Replies
    7
    Views
    353

    I dont understand it when customers install new...

    I dont understand it when customers install new a/c 410a and still keep there 30+ williamson furnace. Here in wisconsin i would rather have a newer furnace. At least they are a breeze to work on....
  44. Replies
    32
    Views
    1,859

    I havent had to use it yet. I was thinking the...

    I havent had to use it yet. I was thinking the same thing about internet orders. The app is nice because i look up prices for parts if i forgot to write it on the box.
  45. Replies
    32
    Views
    1,859

    I picked up the victor torch set today and while...

    I picked up the victor torch set today and while i was in there i asked about the discount when ordering from the johnstone app and was told the discount varies monthly. This month 1%.
  46. Replies
    32
    Views
    1,859

    Ill try to check tomorrow when i pick a torch...

    Ill try to check tomorrow when i pick a torch set:grin2:
  47. Replies
    32
    Views
    1,859

    Thats the reason i posted. Its back in the flyer....

    Thats the reason i posted. Its back in the flyer. My local store has 2 so i will try it out. Just a side note do any of you use the johnstone app? I started using it this last winter it works good...
  48. Replies
    32
    Views
    1,859

    I like the way the hoses wrap around the front....

    I like the way the hoses wrap around the front. Sometime ago i had something like that. The cutskill handles day to day brazing? We do mostly residential.
  49. Replies
    32
    Views
    1,859

    Cut skill by victor

    Is this torch set good? I really need oxy/ace. Its at johnstone onsale. What do think?
  50. Replies
    7
    Views
    462

    I should have gotten the indoor wet bulb. Ill...

    I should have gotten the indoor wet bulb. Ill post if i go back.
Results 1 to 50 of 208
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event