Search:

Type: Posts; User: Ben Wulkin

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Google economizer simulator W7212

    Google economizer simulator W7212
  2. Replies
    60
    Views
    9,776

    Guys , I think you are reading too much into my...

    Guys , I think you are reading too much into my question. I know temperature differential demand has been around for a long time. I seem to remember one in photo fashion that "could see" the frost...
  3. Replies
    60
    Views
    9,776

    Any concerns about oil return to the compressor...

    Any concerns about oil return to the compressor due to the defrost infrequency?
  4. Replies
    10
    Views
    1,214

    Guys, these are non adjusting pencil type...

    Guys, these are non adjusting pencil type burners.The pilots and burners are blue and non lifting.The table is located on the serving line, opposite side from the hood. About 15' away.The bottom...
  5. Replies
    10
    Views
    1,214

    Yeah, I agree with you,100%. I have been in...

    Yeah, I agree with you,100%. I have been in contact with the mfg.Their stance is , since it is an erratic problem, it is on the customers end causing the problem. I also agree with them. It is just a...
  6. Replies
    10
    Views
    1,214

    Thanks for the replies guys. These are non...

    Thanks for the replies guys. These are non adjustable burners. I believe the table is about 6 mos. old. The burners are clean, pretty much protected as they sit under a baffle which sits under a pan...
  7. Replies
    10
    Views
    1,214

    Burner not lighting around

    I have been working on a 3 burner NG steam table. Initial call was due to employee losing his eyebrows while re-lighting a standing pilot.They turned the gas supply off . I turned it on and re-lit...
  8. Replies
    22
    Views
    4,108

    Was working on a rural conventional unit,...

    Was working on a rural conventional unit, setting on a concrete pad.Wiring in control panel was spaghetti, sorting out the wiring , when out of the corner of my eye I noticed some of the wires were...
  9. Replies
    56
    Views
    4,718

    was there a rodent like smell ?

    was there a rodent like smell ?
  10. Replies
    59
    Views
    3,772

    I believe a case could be made for and against...

    I believe a case could be made for and against the location of the moisture indicator on the liquid line. All the racks that I work on have the SG located downstream of the drier. Basically as you...
  11. Replies
    59
    Views
    3,772

    A full or clear sightglass is usually a good...

    A full or clear sightglass is usually a good indicator of system charge, but not always. Quite a few of the systems I work on have the sightglass downstream of the filter/drier. If it becomes plugged...
  12. Replies
    59
    Views
    3,772

    I'm anxious to hear their reply too. I thought...

    I'm anxious to hear their reply too. I thought this was an educational forum, not an attack forum.
  13. Replies
    23
    Views
    1,563

    shoulda, woulda, coulda........ I stand by my...

    shoulda, woulda, coulda........ I stand by my original statement.
  14. Replies
    23
    Views
    1,563

    Just curious. Would you agree that an ORI valve...

    Just curious. Would you agree that an ORI valve is placed in the outlet (liquid) line of the condenser, usually remote and placed at or near the compressor /receiver ? That its function is to not...
  15. Replies
    23
    Views
    1,563

    By cycling the second fan you also reduce the...

    By cycling the second fan you also reduce the amount of refrigerant required for low ambient operation.
  16. Replies
    8
    Views
    805

    I've had success with a pressure washer on the...

    I've had success with a pressure washer on the hard dirt. Just need a little more maneuvering room .
  17. Replies
    10
    Views
    786

    I know my hvac class was more the exception than...

    I know my hvac class was more the exception than the rule.My instructor was a retired commercial refrigeration mechanic.We learned commercial refrigeration instead of hvac. Any Vo-Techs close by ?
  18. Replies
    40
    Views
    5,031

    least favorite part of my job, but I've found...

    least favorite part of my job, but I've found when I cash my paycheck , it all spends the same. Non-slip soles a must.
  19. Replies
    8
    Views
    1,277

    My vote is with Sprint .

    My vote is with Sprint .
  20. Replies
    4
    Views
    1,303

    Thanks Rick , good suggestion . The thermistor...

    Thanks Rick , good suggestion . The thermistor is located there. Unfortunately , I disconnected at that junction and still have a reading of infinity.
  21. Replies
    9
    Views
    1,413

    Two more benefits of the electronic would be the...

    Two more benefits of the electronic would be the ease of routine testing and not having to worry about a stress fracture or something vibrating against the cap tubes wearing a hole, and causing loss...
  22. Replies
    4
    Views
    1,303

    Hobart dishwasher

    Does anyone know the value of the thermistor for the wash tank heater at 160F and / or the board check out procedure? The model is C44AW.
  23. Replies
    8
    Views
    1,044

    I think in our industry as well as others in the...

    I think in our industry as well as others in the business of repair , you will find some that are maybe not as well educated as they should be and some that have a little " larceny in the heart "....
  24. Replies
    9
    Views
    1,413

    Finding a unit tripped out on "oil failure" has...

    Finding a unit tripped out on "oil failure" has to be one of the least favorite things that we encounter. There are so many different reasons why the contol will trip out. Everything from an actual...
  25. Replies
    20
    Views
    2,181

    I did at the time(few weeks ago) plan on...

    I did at the time(few weeks ago) plan on replacing the speed controller.It was unhooked and I was unsure of its history.I ordered one in and took it to the job site. I knew the fan motor had been...
Results 1 to 25 of 30
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event