Search:

Type: Posts; User: Mr Bill

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. The same thing that's going to cause the new...

    The same thing that's going to cause the new compressor to fail. :)


    Sent from my iPhone using Tapatalk
  2. Replies
    13
    Views
    355

    Frozen coil, dead furnace!

    Installing the control board below the evaporator is always going to be an accident waiting to happen, like setting a can of gasoline up on top of the mantle of the fireplace. They need to figure out...
  3. Huh! :eek2:

    Huh! :eek2:
  4. Rheem x-13 blower motor speed change automation

    So if the taps are programmed for 2-3-4 ton applications, and for example you had a 4-ton, Rheem told you if you used the 2- ton tap it would be sufficient? You need to call them back and talk to...
  5. Sometimes not all taps are programmed, the mfg....

    Sometimes not all taps are programmed, the mfg. sometimes only programs the taps for needed for that system to operate correctly. Before I got to strung out on creating an A/B control you might want...
  6. Replies
    58
    Views
    1,458

    kids these days

    That's funny! :)


    Sent from my iPhone using Tapatalk
  7. Replies
    58
    Views
    1,458

    You work harder than most "old folks" you know?...

    You work harder than most "old folks" you know? That's like saying I drink less than most alcoholics, was there a message here? :)


    Sent from my iPhone using Tapatalk
  8. Replies
    18
    Views
    600

    And I would have also replaced the board at my...

    And I would have also replaced the board at my expense, we agree on that.




    This is where they went wrong, it's a pass the buck world. When we have issues related to defects from the factory,...
  9. +1....We also need to remember cold air drops, so...

    +1....We also need to remember cold air drops, so a lot of the up is going down and helping the down short cycle.
  10. You positive your not pulling any outdoor air in,...

    You positive your not pulling any outdoor air in, maybe through bath or kitchen vents doggy door etc? Is has been exceptionally humid in Houston. If the system is short cycling it will effect your...
  11. Replies
    18
    Views
    600

    It hard to notice a crack in a pan until water is...

    It hard to notice a crack in a pan until water is leaking from it. If you replace a radiator can you tell me it's leaking without water in it? :grin2:
  12. Replies
    18
    Views
    600

    Things do happen, this was not caused by a bad...

    Things do happen, this was not caused by a bad installation, it was a factory crack in the pan that caused the issue. Every company has their own way to do business, we would have just replaced the...
  13. Thread: Bryant txv

    by Mr Bill
    Replies
    172
    Views
    10,021

    After going back on the past 7 jobs out of 10 to...

    After going back on the past 7 jobs out of 10 to change the valve, it's piston time.


    Sent from my iPhone using Tapatalk
  14. Trane stopped itself - condensor coil design flaw - costing me a bundle & delay

    I will never again in my life depend on any labor warranty unless it's a mfg. warranty. I got burnt bad a few years back on those 3rd. party warranties. Don't have to slap me but once. :)


    Sent...
  15. Thread: Bryant txv

    by Mr Bill
    Replies
    172
    Views
    10,021

    Bryant txv

    I pulled a bad valve off a Ruud 5-ton 13 AJN today with a Aspen BHA coil and stuck an
    .089 piston in there and the system is working great now! You don't loose that much efficiency from a valve to...
  16. Half price? The online coil has no warranty if...

    Half price? The online coil has no warranty if bought online, the service co. Coil has a least 5-years. So now your going to buy a coil with no warranty, and let someone to install it, that "might"...
  17. Precision, +1.....I see you got my memo. :) ...

    Precision, +1.....I see you got my memo. :)


    Sent from my iPhone using Tapatalk
  18. I remember when Kia first come out, they slammed...

    I remember when Kia first come out, they slammed the tube with commercials. :)


    Sent from my iPhone using Tapatalk
  19. Trane stopped itself - condensor coil design flaw - costing me a bundle & delay

    I will take that to another level, what we are getting today is "no quality" why? Because most folks want cheaper, so the mfg's have received their memo. I don't care if they build a 50 seer, or a...
  20. Replies
    8
    Views
    415

    Why not rectangle, that would be better. ...

    Why not rectangle, that would be better.


    Sent from my iPhone using Tapatalk
  21. Replies
    58
    Views
    1,458

    A selected group. This hippie worked his butt...

    A selected group. This hippie worked his butt off, mowed yards, loved my job at the gas station, could work on my Chevy van during slow times. Drink from a water hose, did not have those cute little...
  22. Thread: Bryant txv

    by Mr Bill
    Replies
    172
    Views
    10,021

    Heck, Ruud don't pay anything. :( Sent from...

    Heck, Ruud don't pay anything. :(


    Sent from my iPhone using Tapatalk
  23. Thread: Bryant txv

    by Mr Bill
    Replies
    172
    Views
    10,021

    Bryant txv

    Go to the local auto parts store and get you a 3/8" compression coupling this will work and work good. I can remember the old Carrier condensers that used to leak were the copper met the aluminum,...
  24. Replies
    10
    Views
    732

    So they installed a new motor, just to come back...

    So they installed a new motor, just to come back out and tell you the unit has to be replaced? Stuff does happen, but I would get a second opinion.


    Sent from my iPhone using Tapatalk
  25. Trane stopped itself - condensor coil design flaw - costing me a bundle & delay

    I agree! but when your racing to stay on the cutting edge of the seer race, quality will suffer.


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event