Search:

Type: Posts; User: mattthehatt80

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Ah ok I'm not thanks.

    Ah ok I'm not thanks.
  2. Replies
    9
    Views
    794

    If its that new chances are sheave may not be set...

    If its that new chances are sheave may not be set up properly either which would change that tension as well. I would suspect that too. How new is it literally that belt should last a while unless...
  3. I can't figure out how to private message on this...

    I can't figure out how to private message on this site.
  4. Well I work for a Large nationwide company now....

    Well I work for a Large nationwide company now. I'm familiar with that unfortunately when they virtually never see you that's what happens.
  5. Replies
    14
    Views
    2,455

    In test mode it's opening on first test? Yes or...

    In test mode it's opening on first test? Yes or no or is this the sometimes?
  6. Yes CMS Mechanical.

    Yes CMS Mechanical.
  7. Replies
    9
    Views
    794

    Sorry that's not a carrier is it. I just looked...

    Sorry that's not a carrier is it. I just looked quickly.
  8. Replies
    9
    Views
    794

    Should be bolts or nut on back side of bottom...

    Should be bolts or nut on back side of bottom plate as well. In between rails theres slide openings you'll have to manually push motor too right after loosening all 4.
  9. Anyone here work for CMS personally?

    Would like some insight as to how they are setup in comparison to other nationwide HVAC contractors before I decide to apply or not. Thanks for your time
  10. Replies
    142
    Views
    5,473

    i confess I am too lazy to press caps and periods...

    i confess I am too lazy to press caps and periods lol.
  11. Replies
    142
    Views
    5,473

    i appreciate your help but i dont see anything...

    i appreciate your help but i dont see anything wrong with what i wrote b4 pretty obvious it means before and some1 =someone so not sure what i wrote wrong there
  12. Replies
    142
    Views
    5,473

    i got the handbook ive looked at it countless...

    i got the handbook ive looked at it countless times today
  13. Replies
    142
    Views
    5,473

    ok thanks for the post guys ill update tomorrow...

    ok thanks for the post guys ill update tomorrow got me concerned now though on connecting rod that was my biggest concern of being possible problem.
  14. Replies
    142
    Views
    5,473

    never left it running long enough to check rla or...

    never left it running long enough to check rla or much else became to noisy was trying not to destroy anything
  15. Replies
    142
    Views
    5,473

    hmm?

    hmm?
  16. Replies
    142
    Views
    5,473

    . oh i know none of it added up hence my...

    .
    oh i know none of it added up hence my irritation this job in general
    i had some1 go out and break vibration eliminator with hammer on me 2 weeks ago so then i get a new one take it out guess...
  17. Replies
    142
    Views
    5,473

    with that being said couldve been a pos line...

    with that being said couldve been a pos line drier hmm got me thinking now
  18. Replies
    142
    Views
    5,473

    thats what i was just wondering myself lol

    thats what i was just wondering myself lol
  19. Replies
    3
    Views
    563

    i quoted a r22 system couple weeks ago it was...

    i quoted a r22 system couple weeks ago it was $7200.00 add about $500 and should cover it for a 48tmf012-610
  20. Replies
    142
    Views
    5,473

    thats what i tried telling them b4 putting $5000...

    thats what i tried telling them b4 putting $5000 into a compressor when unit is a 1983 pos
  21. Replies
    142
    Views
    5,473

    actual reading being takin about 12" downstream...

    actual reading being takin about 12" downstream as there is 2 service ports there some1 put in
  22. Replies
    142
    Views
    5,473

    high temp safety plug, are u asking is that where...

    high temp safety plug, are u asking is that where the leaks at now? and initial high pressure reading b4 startup was about 110 but when it reached 140 it never moved much from there wether running or...
  23. Replies
    142
    Views
    5,473

    yes standard evac and nitrogen holding charge...

    yes standard evac and nitrogen holding charge leak check and so on done and yes i went grabbed different set of guages and checked guages later in day elsewhere
  24. Replies
    142
    Views
    5,473

    then slam head off unit get pissed and leave...

    then slam head off unit get pissed and leave outta ideas for now
  25. Replies
    142
    Views
    5,473

    ok only 72 outside and 75 inside so no load but...

    ok only 72 outside and 75 inside so no load but why no pressure movement maybe 5 psi but discharge line and heads getting hot let me hear it again bam here come the fricking hole in the dam manifold
Results 1 to 25 of 58
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event