Search:

Type: Posts; User: t527ed

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    7
    Views
    223

    :ditto:

    :ditto:
  2. Thread: Ice on shingles

    by t527ed
    Replies
    3
    Views
    176

    sure its piped right? exhaust going out the...

    sure its piped right? exhaust going out the middle pipe?
  3. Replies
    43
    Views
    1,037

    you did not figure anything out, the 130 deg...

    you did not figure anything out, the 130 deg limit is what your furnace calls for. the 140 limit is for the -1 model ONLY
  4. Replies
    43
    Views
    1,037

    the chart you posted is incomplete, it does not...

    the chart you posted is incomplete, it does not show the C3 revision.
  5. Replies
    43
    Views
    1,037

    you have the correct limit installed, you have...

    you have the correct limit installed, you have other problems. please call a tech.
  6. Replies
    3
    Views
    230

    most circuit boards are set up to open R if an...

    most circuit boards are set up to open R if an unsafe condition exists.

    get someone in there to check it out.
  7. Replies
    3
    Views
    325

    combustion air has become a big deal around here...

    combustion air has become a big deal around here in the last few years.
  8. Replies
    18
    Views
    1,058

    had one section of a town near us that used the...

    had one section of a town near us that used the old slant tops, never saw plastic line sets on any that we replaced.
    they were easy to work on though, except sometimes trying to find a condenser fan...
  9. Replies
    18
    Views
    1,058

    GE before being bought by Trane was using the...

    GE before being bought by Trane was using the plastic suction line with quick connect fittings. believe it was mainly on the larger size units.
  10. only ones i ever saw used a pressure actuated...

    only ones i ever saw used a pressure actuated push rod using the units discharge pressure to modulate damper position.
  11. double hernia and had my 4 front bottom teeth...

    double hernia and had my 4 front bottom teeth broken off when my brother slipped off a fitting and hit me in the mouth with a wrench. worst part about that was we were on a roof in the winter and the...
  12. Replies
    7
    Views
    423

    you should be fine with disconnect pulled, if...

    you should be fine with disconnect pulled, if still worried find and shut off circuit breaker.
    melted or burnt connections is almost always due to a loose connection or undersized wiring.
  13. Replies
    7
    Views
    423

    call the city inspector and find out what...

    call the city inspector and find out what requirements are for repairs on rental properties. in NJ a licensed electrician can't work on a rental property he owns.
    a homeowner can do whatever he...
  14. Replies
    2
    Views
    227

    warm moist air from house is rising up into duct...

    warm moist air from house is rising up into duct system and condensing.
    it is a common problem with attic a/c only systems.
    you can try sealing off all supply and return grills for the winter or...
  15. Replies
    16
    Views
    457

    +1 you cannot pull return from room furnace is...

    +1
    you cannot pull return from room furnace is in if it is an 80% furnace, risk is that you could pull exhaust into house.
  16. Replies
    16
    Views
    457

    is the furnace 80% afue or is there a gas water...

    is the furnace 80% afue or is there a gas water heater in the same room?
    if so you must run return duct.
  17. Replies
    41
    Views
    1,544

    i would not use stab on connections for power...

    i would not use stab on connections for power supply to unit, they have a nasty habit of burning off as they age.
  18. Replies
    14
    Views
    712

    we use 2 of these, guy in attic and guy below...

    we use 2 of these, guy in attic and guy below both do it and then you just punch out the circle.

    roto zip if plaster.
  19. Replies
    21
    Views
    952

    thumbs or a dead blow hammer. :.02:

    thumbs or a dead blow hammer. :.02:
  20. Thread: Service vehicle

    by t527ed
    Replies
    6
    Views
    451

    i used 4x4 pick up with utility bodies for about...

    i used 4x4 pick up with utility bodies for about 20 years, realized for my area it really was a waste of money.
    truck i use now is an E-350 with a knapheide work body, its better in the snow than i...
  21. +1 i tell them the same thing.

    +1 i tell them the same thing.
  22. Replies
    5
    Views
    297

    what is the temperature of your incoming cold...

    what is the temperature of your incoming cold water?
    with this winter the cold water supply is COLD this year.
  23. Thread: Whistling TXV

    by t527ed
    Replies
    10
    Views
    558

    did you try adding some refrigerant to it? low...

    did you try adding some refrigerant to it?
    low ambient control it the only reason your head pressure is getting as high as it is, i would add some gas before condemning a txv.:.02:
  24. you will never have a large "rush" of water...

    you will never have a large "rush" of water coming down the exhaust pipe and into the inducer unless you pour it down the pipe. :toetap:
    only time water will back up into inducer is if a drain plugs...
  25. commonly referred to as " letting the smoke out"...

    commonly referred to as " letting the smoke out"
    could have been something bad from the factory, most likely though it was caused by being wired wrong.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event