Search:

Type: Posts; User: tech37

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    4,708

    What a POS install.

    What a POS install.
  2. Replies
    14
    Views
    2,249

    The guy filling was trying to round charge up to...

    The guy filling was trying to round charge up to the next highest 10$ figure?
  3. Replies
    29
    Views
    4,078

    Looks like the installer left his tools behind.

    Looks like the installer left his tools behind.
  4. Replies
    7
    Views
    1,901

    :eek2:Another reason for sterilization laws so...

    :eek2:Another reason for sterilization laws so "stupid" genetics don't carry to the next generation!
  5. Replies
    42
    Views
    3,308

    What happens in the guest house stays in the...

    What happens in the guest house stays in the guest house!;)
  6. Replies
    16
    Views
    2,550

    I get clausterphobic just looking at that pic.

    I get clausterphobic just looking at that pic.
  7. Replies
    30
    Views
    3,368

    You tell 'em Bob !!!!

    You tell 'em Bob !!!!
  8. Replies
    22
    Views
    2,962

    Hey, Isn't That some of Curly Howard Fine's...

    Hey, Isn't That some of Curly Howard Fine's handywork?
  9. Replies
    13
    Views
    1,829

    Wonder if there was any paperwork left in evap....

    Wonder if there was any paperwork left in evap. section?
  10. Replies
    6
    Views
    1,516

    Bet they run some high head pressures with that...

    Bet they run some high head pressures with that stuff trying to pass through condensers.
  11. Replies
    1
    Views
    719

    :censored:Talked to tech support once and he...

    :censored:Talked to tech support once and he recommended using a crescent wrench on agitator center and stricking with hammer to unlock as gear motor force against bin ice sometimes makes this step a...
  12. Replies
    15
    Views
    1,162

    I agree. Sounds like the sensing bulb is loosing...

    I agree. Sounds like the sensing bulb is loosing pressure.
  13. Replies
    25
    Views
    4,393

    Isn't #1 & #3 the same unit in a before and after...

    Isn't #1 & #3 the same unit in a before and after shot ?:anyone:
  14. Replies
    123
    Views
    30,845

    Kinda looks like mine at the end of a busy week...

    Kinda looks like mine at the end of a busy week but it don't stay like that much longer cause it bugs me too much.
  15. Replies
    8
    Views
    1,717

    Considering the amount of corrosion on the draft...

    Considering the amount of corrosion on the draft housing, how was the rest of the heat exchanger?? Looks questionable...
    I agree! Bet theres a hole somewhere unless the HE has been replaced b4.
  16. Replies
    22
    Views
    1,998

    Only eleven years old? Without maintenance thats...

    Only eleven years old? Without maintenance thats like you kicking off at "only 700"!
  17. Replies
    29
    Views
    2,239

    Does this Evaporator have a line to line heat...

    Does this Evaporator have a line to line heat exchanger? I once had a unit with similar symptoms and found that the liquid line that dips into the suction line,
    had a small crack in it. It would...
  18. Thread: -

    by tech37
    Replies
    7
    Views
    559

    _--'.,,.,.,,..,"//|\\

    _--'.,,.,.,,..,<>"//|\\
  19. Replies
    18
    Views
    1,607

    McQuay RTU's are beginning to use these type.

    McQuay RTU's are beginning to use these type.
  20. Replies
    40
    Views
    6,229

    I'm gonna have niightmares for weeks.

    I'm gonna have niightmares for weeks.
  21. Replies
    17
    Views
    2,780

    Too funny! Youd thinke sum1 wood seee thu tag wuz...

    Too funny! Youd thinke sum1 wood seee thu tag wuz mispilled.
  22. Replies
    15
    Views
    2,837

    I think he's talking about the three phase...

    I think he's talking about the three phase breaker label being continued in marker on wall. also looks as if it was corrected.
  23. Replies
    4
    Views
    437

    I agree, save the customer $$$ by replacing BAD...

    I agree, save the customer $$$ by replacing BAD design parts.
  24. Replies
    16
    Views
    2,760

    :confused:The fact she asked you why her son had...

    :confused:The fact she asked you why her son had it points to the problem directly. Some people....:confused:
  25. Replies
    26
    Views
    5,006

    I'd agree with Mike, bet it's been dropped.

    I'd agree with Mike, bet it's been dropped.
Results 1 to 25 of 36
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event