Search:

Type: Posts; User: dmp3_16hvac/r

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    2,106

    kfc

    well I have been getting a lot of everythings,, mostly cooler this past week, the owners of of franchase want a pm program but,, I don't have time. as for Micro-waves my boss always tells me just...
  2. Replies
    4
    Views
    665

    well I haven't had any more problems with the...

    well I haven't had any more problems with the ignition module, I did addd the flue extension as per the factory, but I also had found out from other contractors that they were having problems with...
  3. Replies
    13
    Views
    2,106

    KFC microwaves

    yep got to love those Amanas, KFC use's 3 the KFC1 , KFC 2 and the RPSk9, I work for the KFC so Iget to see them lots, but they really don't break down all to often,, have more problems with deep...
  4. Replies
    4
    Views
    665

    yep appox 26 volts to the ignition module and 26...

    yep appox 26 volts to the ignition module and 26 volts out to the gas vale, it just isn't sparking, replace module and its fine for a while and then same problem all over, I will discuss itwith...
  5. Replies
    4
    Views
    665

    Ignition problems

    I am looking to see if any one else is having a problem with ignition modues.
    I am working on a Carrier 48DJE009520, serial number 4491G4300. The problem is it has gone through 4 ignition modules in...
  6. Replies
    12
    Views
    1,589

    I found a new web site today lots of help,...

    I found a new web site today lots of help, amnuals and such
    WWW.ckps.com
  7. Replies
    12
    Views
    1,589

    Ice makers

    I have een to my wholesalers for the Manitowoc and to the Hoshizaki one day, both helped some.
  8. Replies
    12
    Views
    1,589

    training

    I have been to the Frymaster one day training it was presented by a local supplier, I have been to a Amana 1/2 day seminar, most of those can be found buy calling appliance wholesalers, I also went...
  9. I ran a service company for 3 and halfs years,...

    I ran a service company for 3 and halfs years, worked on all kitchen equipment, it is greaasy messy, but I enjoy the challenge. I left that and now work for KFC, I do all the HVAC/r and kitchen...
  10. Thread: Cheap

    by dmp3_16hvac/r
    Replies
    2
    Views
    1,114

    if the gas valve does not repond and close and...

    if the gas valve does not repond and close and they have had problems with the knob replace the valve the next thing that can happen is for the gas valve to start on fire or bolw up.
  11. Replies
    15
    Views
    1,320

    those flakers need to be cleaned every couple of...

    those flakers need to be cleaned every couple of months, they do not like any build up in the ice barrel or water system
  12. Carrier

    or you try Auer steel in MIlwaukee they may have someone they can reccomend in the Mad town area
  13. Replies
    2
    Views
    706

    more information

    the unit is a Trane YCD120B3H0AA, I returned today and it is running fine,,
    stil have no idea, neither does Trane as to why the other board blew up.
  14. Replies
    2
    Views
    706

    A question for all you out there I was working on...

    A question for all you out there I was working on a trane rooftop,, the main board which contorls everything had the corner where the heat relay totally blown out,, checked everything couldn't find a...
  15. Thread: parts

    by dmp3_16hvac/r
    Replies
    6
    Views
    1,374

    FMP is good for parts, there is also PArts Town,...

    FMP is good for parts, there is also PArts Town, COnsolidated only sells to repair contractors who resell them them,
  16. Replies
    12
    Views
    1,982

    I work for KFC,, we have started using DUKE...

    I work for KFC,, we have started using DUKE holding trays, I have done work on them before didn't care for the way you have to disassemdle them to replace the heater, would like to be able to use the...
  17. Replies
    6
    Views
    1,174

    yes you have to love all the grease in the Henny...

    yes you have to love all the grease in the Henny Penny fryers, it just hangs and waits for the right moment to drop on your head, the steam works pretty good but it does make a drippy mess under it.
  18. Replies
    21
    Views
    2,580

    is the motor turning in the right direction if it...

    is the motor turning in the right direction if it is running wrong you can draw high amps, but move little air, you need to know direction of fan.
  19. Replies
    3
    Views
    1,326

    one thing I have found the terminals will burn...

    one thing I have found the terminals will burn off if they are not crimped tight, and the wire has to be clean before you crimp it.
  20. I think it is great as I have 10 years doing...

    I think it is great as I have 10 years doing commerical cooking equipment and 20 doing HVAC, they do get put togather sometimes
  21. Thread: carrier

    by dmp3_16hvac/r
    Replies
    11
    Views
    916

    I have had some units due that, i found that the...

    I have had some units due that, i found that the contact was drawing excessive amps,, in my case the fuse was 3 amps and it draw 3.7 causing it to trip.
  22. Replies
    8
    Views
    1,013

    removal of R410a needs to be done in a liquid...

    removal of R410a needs to be done in a liquid state, R22 can be done as a gas. most of the new compound refrigerants need to be removed in a liquis stae as much as you can, otherwise you change the...
  23. Replies
    10
    Views
    850

    Good Luck in your new direction, as someone who...

    Good Luck in your new direction, as someone who has been my own boss, I gave it up. Family meant more to me. I Ran 24/7/365 for 15 years, missed a lot of family time, every holiday you have calls,...
  24. Replies
    10
    Views
    715

    check the rotation of the blower, if the unit is...

    check the rotation of the blower, if the unit is running wrong it will have high amp draw, it will still move a little air. is this a circle type up draf exhaust? if it is the direction is usually...
  25. Replies
    15
    Views
    3,226

    those fryers are always fun to work on once the...

    those fryers are always fun to work on once the grease gells, exspecially around switchs, we have them where there is 2-3 inches of grease, that once you touch it sticks to everything. got to love...
Results 1 to 25 of 68
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event