Search:

Type: Posts; User: frostedfingers101

Search: Search took 0.00 seconds.

  1. Danfoss Tp7000 Programmable Stat

    hello, hope to get some info on this stat, installed one today but forgot user guide on job. it does have remote sensor, danfoss site does not give me user info for 7000 just 5000 which does me no...
  2. Replies
    2
    Views
    753

    thanks for reply techtalker, i havent found one...

    thanks for reply techtalker, i havent found one to open at stamped temp, i was seeing it at 40f over that temp. i would say its bad , but a new one done the same , just doesnt make sense to me that...
  3. Replies
    2
    Views
    753

    high limit

    hey guys, hope to get some information, during pm on many carrier units, when testing high limit ( HH18HA148A L160-40 ) unit well most did not kick out untill 195f, spoke to carrier service tech...
  4. Replies
    10
    Views
    1,428

    thank you everyone i appriciate, i did ssay to...

    thank you everyone i appriciate, i did ssay to change contact but can not find it its a GE LB1A1 din rail mount , well thanks again everyone :D
  5. Replies
    3
    Views
    612

    Johnson Aro Unit

    hoping someone can help me, i will be going to work on this unit tomorrow, i have never seen one. i didnt know if any one else has, im looking for a website, M# AR75CP4MG hope someone can help
  6. Replies
    10
    Views
    1,428

    thanks, i thought it was bad contact somehow,...

    thanks, i thought it was bad contact somehow, well what i said any way:o oops my bad
  7. Replies
    10
    Views
    1,428

    1 burnt wire 3phase

    i was working on a humidifier, from the contact, line side 208v, noticed load side had middle leg burnt about an inch from contact starting in contact. i unwired and ohmed out heaters and were good,...
  8. Replies
    2
    Views
    611

    thank you small change i will try it and see i...

    thank you small change i will try it and see i appriciate it
  9. Replies
    2
    Views
    611

    Humidifier

    hello all, hope someone can help me

    i was working on a dri-steem M# VLC 2-1 S#1097191 208v 1ph, during PM found unit shut off, checked unit and did not find anything unusual. i turned power...
  10. Replies
    4
    Views
    7,305

    thanks guys for reply, i did not check...

    thanks guys for reply,

    i did not check inlet and outlet of gas pressure due to when it lit, all appeared normal, it was being pulled in and looked good. it was a horizontal left unit and with...
  11. Replies
    4
    Views
    7,305

    roll out switch

    ok guys, not sure if what i did was right, so any info would be greatly appriciated. i was on an Air-Pro furnace M# AF80MPA07583 S# 4601A01129 i have found its made from lennox, but anyway, i found...
  12. Replies
    30
    Views
    1,804

    i tend to stick with jim beam although i did...

    i tend to stick with jim beam although i did try knobb creek and it was good
  13. Replies
    22
    Views
    2,255

    I was told the difference is sheave - is what...

    I was told the difference is
    sheave - is what is on the drive motor
    pulley - is whats on unit to be operated by drive motor

    i then have also heard people call it a pulley no matter what...
  14. Replies
    3
    Views
    465

    i started a new job last monday, on first day was...

    i started a new job last monday, on first day was told need to go this new account they have, need to look at system and see how to get motor starter for a/h connected. i was told a certain person...
  15. Replies
    1
    Views
    615

    ok heres the deal, working on a trane low ambient...

    ok heres the deal, working on a trane low ambient condenser with a w973j logic control. a/h in basement, 24x24 fresh air intake with damper and belimo 24v motor. wired damper according diagram, i...
  16. Replies
    8
    Views
    1,093

    thanks goodhumor. even thuogh 2 were bouncing i...

    thanks goodhumor. even thuogh 2 were bouncing i could see it was actully not full of liquid is this due to bypass not letting diischarg in top, i dont recall line being hot, also did not know to...
  17. Replies
    8
    Views
    1,093

    thanks mark,gerry and smiles, i think i need too...

    thanks mark,gerry and smiles, i think i need too look and figure this out, sounds like maybe vale not opening to keep pressure in tank to force full sight glass

    much appriciated thank yuou
  18. Replies
    8
    Views
    1,093

    surge tanks

    not sure exactly kind of new to racks i know theres a bypass from discharge to top of it which was not open, s.v in line
  19. Replies
    8
    Views
    1,093

    hello new to this, hope to get some helpful info...

    hello new to this, hope to get some helpful info

    was working on hill phoenix rack, r404, head pressure at 180# operating in desired range set for, suction in desired range, dont recall...
Results 1 to 19 of 21
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event