Search:

Type: Posts; User: danibal006

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    677

    X2. Also, 58* compressor superheat is high, I...

    X2. Also, 58* compressor superheat is high, I would also agree that the evap is being starved. 20* condenser split on the low side. No thermostat? Is it using pressure to control temperature? I guess...
  2. Replies
    23
    Views
    1,087

    I stock the Turbo 200 universal run capacitors,...

    I stock the Turbo 200 universal run capacitors, but had not noticed the universal start caps... will have to look for those. Where do you get the Amrad's, Sid's or CD Jones?
  3. Replies
    23
    Views
    1,087

    I use the supco 3-in-1 kits, and have never used...

    I use the supco 3-in-1 kits, and have never used any of the hard-start kits I have. The 3-in-1 kits have a capacitor, overload and relay that can be used to temporarily replace the start components...
  4. Replies
    76
    Views
    3,352

    I thought the concern with running compressors in...

    I thought the concern with running compressors in a "deep" vacuum was arcing of the fusite pin terminals. Granted, certain compressors handle this better than others (like scrolls). So, my question...
  5. Replies
    46
    Views
    2,680

    When I was going to school, the majority of...

    When I was going to school, the majority of students were getting resi jobs, mostly because those were the connections that the school had established with local businesses and contractors. I was the...
  6. Replies
    5
    Views
    319

    You can also check the water level probe that...

    You can also check the water level probe that sits next to the pump on the underside of the trough. Verifying that there is voltage to the coil would also confirm that the level probe is working. If...
  7. Replies
    16
    Views
    881

    Fantastic. Thanks so much for your help :grin2:

    Fantastic. Thanks so much for your help :grin2:
  8. Replies
    16
    Views
    881

    I will have to look into that. I found it very...

    I will have to look into that. I found it very accurate and reliable, would love to keep it around.
  9. Replies
    16
    Views
    881

    I had gotten the original BluVac when I first...

    I had gotten the original BluVac when I first started out... then UEI bought them out. Didn't realize YJ bought in too. I keep it as a spare now, as I use the one that came with my YJ digital...
  10. Replies
    27
    Views
    1,265

    I use Sil-Phos brazing rods almost exclusively...

    I use Sil-Phos brazing rods almost exclusively for majority install and repair work. I believe it has a 5% silver content. 15% silver (often comes in a coil) is usually used for brazing different...
  11. Replies
    22
    Views
    1,166

    Absolutely. Part of that relationship is...

    Absolutely. Part of that relationship is educating the customers we work with. Tricky part is doing so in a way that does not insult their intelligence (or lack of common sense) :whistle:
  12. Replies
    22
    Views
    1,166

    I would be surprised if the ice releases...

    I would be surprised if the ice releases properly, even after bending the fins and filing the burrs off. I recently had a manager from a particular fast food chain do the same thing with a fairly...
  13. Replies
    6
    Views
    374

    Are you asking if your math is correct, or if the...

    Are you asking if your math is correct, or if the superheat is correct? 20* SH measured near the compressor would be good, but 5*-8* at the evaporator is what I would set it for.
  14. The imperial fryer has a new gas valve, but it is...

    The imperial fryer has a new gas valve, but it is leaking by when closed? Is it installed in the correct orientation (i.e, not backward)? If it is in the correct orientation, make sure there is...
  15. Replies
    9
    Views
    1,635

    I was curious, only because I have come across...

    I was curious, only because I have come across three different instances where an installer used sta-brite to solder the TXV. One install in particular, two out of four evaporators had leaking TXV's,...
  16. Replies
    9
    Views
    1,635

    MAAP torch?

    MAAP torch?
  17. Replies
    6
    Views
    2,442

    Understanding the sequence of operation will go a...

    Understanding the sequence of operation will go a long way towards diagnosing any piece of equipment. Knowing WHAT is supposed to happen WHEN is particularly important with steamers.

    Also, it goes...
Results 1 to 17 of 17
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event