Search:

Type: Posts; User: enart9591

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    1,023

    Have you considered a "Bard" wall mounted unit...

    Have you considered a "Bard" wall mounted unit such as is used on mobile jobsite trailers? You will probably have to build something to hide it, but that shoudn't be a problem.
  2. Replies
    8
    Views
    887

    Turn it off?

    Turn it off?
  3. Thread: Help needed

    by enart9591
    Replies
    7
    Views
    699

    Have you tried, Trane, York, Carrier, or McQuay?...

    Have you tried, Trane, York, Carrier, or McQuay?

    All of these companies have service groups.
  4. Check out this site. It has helped me thru some...

    Check out this site. It has helped me thru some rough times.

    Good Luck and God Bless


    http://www.anewlife.org/
  5. Replies
    13
    Views
    1,045

    Does this system have glycol in it? If so, was...

    Does this system have glycol in it? If so, was the coil designed for glycol?
  6. Replies
    2
    Views
    930

    You won. Where do I send the money?

    You won. Where do I send the money?
  7. Replies
    17
    Views
    1,504

    You may be on to something with the low control...

    You may be on to something with the low control voltage. It is very possible that the coil is not drawing in as quickly/firmly as it should.

    Another thing I would check is your cycle time between...
  8. Replies
    14
    Views
    1,730

    What model chiller? RTAA or RTAC? How many...

    What model chiller? RTAA or RTAC?

    How many compressors in the machine (not sure from your post)?

    What are the operating pressures and temps for both compressors.

    Are the compressors running...
  9. Replies
    15
    Views
    1,319

    Anything is possible. Could it have been short...

    Anything is possible.

    Could it have been short cycling on low pressure due to the coil being iced up?

    Could the compressor have been slugging liquid refrigerant and overheated the motor?
    ...
  10. Replies
    19
    Views
    1,340

    I will add that on a flooded condenser the cooler...

    I will add that on a flooded condenser the cooler entering water is in contact with the condensed refrigerant before it flows to the evaporator. It is because of this that you can have a negative...
  11. Replies
    19
    Views
    1,340

    The approach temperature is determined by the...

    The approach temperature is determined by the design (from the engineers) of the machine and is dependent upon the type of machine in question.

    The evaporator approach on a centrifugal chiller...
  12. Replies
    19
    Views
    1,340

    Depending upon the age of the AHU, a 10 degree...

    Depending upon the age of the AHU, a 10 degree water side temperature rise is a fairly common design, but in recent years I have seen 12, 14, and even 16 degree design rise thru the coil.

    If you...
  13. Thread: Sex on Mars

    by enart9591
    Replies
    0
    Views
    889

    The year is 2222 and after accumulating enough...

    The year is 2222 and after accumulating enough frequent
    flier miles, Mike and Maureen land on Mars. They meet a
    Martian couple and are talking about all sorts of things.
    Mike asks if Mars has a...
  14. Replies
    52
    Views
    7,321

    esornivram, I think I have one of these units...

    esornivram, I think I have one of these units with the problems you have described. Who should I contact to get authorization for repairs?
  15. Replies
    2
    Views
    508

    Anyone had experiance with Advantage contactors...

    Anyone had experiance with Advantage contactors in a unit mounted starter blowing up?
  16. Replies
    11
    Views
    1,671

    Go to Sporlan's website.

    Go to Sporlan's website.
  17. Replies
    12
    Views
    1,046

    Welcome christine.

    Welcome christine.
  18. Have you checked the actual temp at the condensor...

    Have you checked the actual temp at the condensor sensor with an accurate temp probe and compared it to what the readout on the panel? With the subcooling that you have (40 degrees) it is likely that...
  19. First, let me say that you really need to read...

    First, let me say that you really need to read the IOM on this machine to truly understand how it operates. Second, you must not try to troubleshoot the machine without having your gauges hooked up....
  20. Replies
    31
    Views
    1,476

    Is it "Rats" or "Rates" that you are afraid of. ...

    Is it "Rats" or "Rates" that you are afraid of.

    I can tell you that there are a lot of "Rats" in this buisness, but most of them walk on two legs.
  21. Replies
    26
    Views
    1,584

    Most, if not all, professional technicians expect...

    Most, if not all, professional technicians expect benefits or an equivelant additional compensation to cover the costs of purchasing insurance and putting away money for retirement.

    I wonder if...
  22. Replies
    21
    Views
    3,379

    Payson, I have been reading your threads for a...

    Payson, I have been reading your threads for a while now and agree with truck31. I think you would do well in commercial.

    Contact the Trane CSO (commercial sales office) in Phoenix.

    Do not be...
  23. Replies
    24
    Views
    1,796

    There has to be a balance. Techs have lives too.

    There has to be a balance. Techs have lives too.
  24. Thread: Centravac

    by enart9591
    Replies
    5
    Views
    866

    Is this a unit mounted starter or remote? What...

    Is this a unit mounted starter or remote? What brand of machine? Does the starter have the intregal circuit board for the coil?
  25. The most important things to me when hiring a...

    The most important things to me when hiring a tech is do they have a thorough grasp of the basics. That is, do they "really" understand the refrigeration cycle and the operation of all the components...
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event