Search:

Type: Posts; User: TEK723

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    32
    Views
    3,110

    Not a person that like HONDA that's for sure!

    Not a person that like HONDA that's for sure!
  2. Replies
    50
    Views
    5,509

    I may be close

    Im from Robinson Twp PA
  3. Replies
    21
    Views
    1,152

    termination

    Does the vent pipe extend 8" from the wall? Or does it just have an ell on it?
  4. I say what Twilli said:D

    I say what Twilli said:D
  5. Replies
    16
    Views
    1,527

    Isn't the coil tubing to thin for repair? Hoe do...

    Isn't the coil tubing to thin for repair? Hoe do you repair them?
  6. Replies
    5
    Views
    600

    ???

    are these wall of shame pictures?
  7. Replies
    78
    Views
    3,785

    Hotwater tank

    I believe you said you had an 80% furnace. Was the flue tied in with the hot water tank? Does the tank flie have a 3" liner in the chimney?
  8. Replies
    12
    Views
    4,326

    I went through that myself last month on my first...

    I went through that myself last month on my first GB-142 install. It was driving me nuts trying to figure out how the AM10 was supposed to be mounted!!! I call my supplier and he said upside down....
  9. stop it

    You guys are making this up! lol
  10. Replies
    98
    Views
    6,011

    lower trap

    In the picture, it would appear that it should be a deeper trap.
  11. Replies
    98
    Views
    6,011

    I would think the water would be pushed out of...

    I would think the water would be pushed out of the trap being on the positive side of the fan.
  12. Replies
    3
    Views
    496

    Thanx

    Thank you, obxtech! Do you use a software for duct sizing?
  13. Replies
    3
    Views
    496

    Load Calculation Software

    I'm interested in buying software for load calculations. I see R.H.V.A.C. RESIDENTIAL CALCULATION and J8 for windows on the ACCA site. Does anybody have any recommendations?
  14. Check pioes

    See if you suction line is freezing up at the furnace or outside.
  15. Replies
    11
    Views
    979

    me too

    Was born and raised in it, Dad was an ac tech and so am I. I feel better in the cooler temps. Just the way I was made! lol
  16. Thread: Static Pressure

    by TEK723
    Replies
    3
    Views
    622

    Static Pressure

    I've read here to take statis pressure readings berfore the evap coil and after the filter on a furnace. If you were checking a evap air handler, would you test further doen stream to avoid VP?
  17. Replies
    33
    Views
    1,781

    I second that !

    I second that !
  18. Replies
    15
    Views
    1,346

    18 years old

    I updated my Mothers system 8 years ago after my father passsed away and I guesstimated it was 30 plus years old and still operating. I thought about calling the company to see if they wanted to do a...
  19. Replies
    12
    Views
    1,881

    Could be a restriction in the liquid line. I...

    Could be a restriction in the liquid line. I found one after a compressor failure. Copper dryer/strainer acting like a metering device.
  20. Replies
    25
    Views
    1,913

    Looks like a poor braze job to me also. I don't...

    Looks like a poor braze job to me also. I don't see a kink.
  21. Replies
    11
    Views
    3,742

    2.5 tons

    2.5 tons
  22. Thread: 410 A Help!

    by TEK723
    Replies
    17
    Views
    1,648

    Good call cat man!

    Good call cat man!
  23. Replies
    22
    Views
    1,702

    Dam near took the words right out of my mouth....

    Dam near took the words right out of my mouth. Try to anticipate your journeymen. I'm new to the site, and read alot of great stuff. Your alright beenthere.
  24. Replies
    34
    Views
    3,019

    I responded to the wrong thread shallowluv,...

    I responded to the wrong thread shallowluv, sorry! still learning the site.
  25. Replies
    34
    Views
    3,019

    WOW

    WOW
Results 1 to 25 of 37
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event