Search:

what gain would resistors be between terminals on dual "run" capacitors..seeing them in trane parts stores..i know why start capactors would...if it would make the run capactor last longer i would...

i got my pair gave to me from retired a/c mechanic......have seen them go as low as 20.00 on ebay over the years........well worth that......if you are installing with the small thermostat wires in a...

i may have missed it on here but the best crimper's i have ever used is the amp 59250 that aircraft have used for sometime.....i have seen nothing listed here that comes close..ebay would be the best...

if i could spell i would have went futher in life,look at jordan david grips,overshoes,i have been getting the jd912 4"..i haven't worn the first ones out,keep my feet dry in rainy times also..they...

we have used "gripps" with good results,they are like an overshoe that goes over your shoes,they have like coarse sand paper strips on bottom that holds up very well,can't wear them on an inside or...

that part is on this unit,has 3 knob screws attaching it,looks like it would go on front of a snow sled....it's just this unit is probably bigger in the cooler months than needed so it's wasteful to...

thanks for reply's...and yes i want it off at lower door level,not by opening door..i was reading in the scotsman handbook and it goes into more depth that the service manual on the cm3...

this unit with the htb555 bin gets extremely full before the "eyes"will turn it off,has anybody used the a37749-001 bin conversion kit?does it still use the eyes to tell controller that its making...

tried to make ice cream sat.did ok for the first 30mins..then beater motor started kicking out again....black wire going to beater motor pulls 6 amp starting in the begining....when it messes up...

i pulled the motor and drive assy and took to a motor repair shop,they could not fine anything wrong,they could load it and that did fine...disassembled drive that was ok.....the rta overload is set...

have acquired uc 511 softserve machine..... impressive machine,never used a coldelite before....it runs fine,makes product fast.when it makes and shuts down alls still well...when you pull the handle...

called johnston today,they said 45/5 was fine.....still wonder why 46/6 was oem....is their a formula to figure what size capactor is used....the condensor side is what bother's me

from the info i wrote down before it[old one] has a #27L568 on it and # b9457-72001/green...all i know to tell you

goodman,cplt36-1......s.n.038409403 thanks for your reply

i remember that a start capactor is not real exact but run capactors are suppost to be the same,my unit has a run capactor dual 46/6 370v body is round.....i have a 45/5 440v. would that cause a...

thanks wild leg,i can't post pictures...it sounds like if it's impossible to get this part then it goes in the trash ...lasting for evermore time's came to an end...

i found,inside the freezer,a panel that had a giant temp control dial on it.behind that panel in a black square box with 2 set temp screws and 6 big wires going to it,and a sensor bulb that secures...

very sure on the model no#...i believe it was bought in 62 or 63....i will relook for this timer and diagram today....sounds like you have been there.....thanks for the info

yes,i looked for a diagram on the back bottom,and everywhere i could think of where it could be hidden,no luck....and yes it is the coil's inside on the back that are frozen....found no clock or...

Have a GE freezer that uses a reversing valve that defrost it.It has froze up the coils in the back.The model # is ca376xb w.....sn..sx100479.i would love to have a diagram to see what makes it...

thanks for the replies,from them it sounds like as a rule the valve failure would be the installers fault because of too much heat brazing the lines in than a faulty valve from factory and he for...

he said the leak was at service core,and it was working so i do feel it leaked out enough to freeze up...from what you have said,it sounds like you are eating the repairs for the first year and not...

had a heatpump installed in a rent house 9 mons ago,800 sq ft house,never had duct work so,because of renthouse paid to have it done by a certified man who i've used before and trust.a goodman was...

looked at it, and mark you are right,i will need to replace the whole thing,why would they do a dumd thing like that?i thank you for straighting me out!

yes, they are inside the cabinet,and yes an auto tool,that i have,regular size on one end,and bigger on the other,does fit it,i guess i'm going to have to make something to work with the yellow...