Search:

Thanks I pretty much did the same thing because the unit I’ve installed is a multi head unit and it doesn’t have the male connectors on them so made 3 of them so I can diagnose the individual wall...

I just got the DrSmart Inverter Air-Conditioner Detector tool to help me troubleshoot Mini Splits Units and I have not use it yet and I was wondering was it worth the purchase? And if anyone have had...

Hello I have the Fieldpiece MG44 Wireless Micron Gauge and I was wondering how often should you clean them? I noticed that after a couple of uses the gauge started bouncing around and wasn’t reading...

I want to thank everyone for their input it is greatly appreciated!

Hello

I have a big Mini Split installation project coming up and I’m going to have to drill through the side of the building which is either brick or cinder block and I’m going to be drilling a...

I was just wondering how to correct a system that has high static pressure on a Downflow Furnace if it had a clay Perimeter Ductwork System.

Thanks I was always wondering about this!

Just was wondering if you’re testing a Downflow Furnace and the house sits on a slab and it has clay ductwork around the perimeter of the home will the static pressure be higher than the average...

Is this specifically made for Commercial Rooftop Units?

Hello
I was wondering do they make ECM Motor testing tools for rooftop units? I have the Supco one for residential but was wondering if they made one for commercial rooftop units?

Thanks!

Hello,

I’m just curious I installed this Goodman GMES801005CNAA Furnace in and it’s not even 3yrs old and I went to do my annual clean & check on it and the board was bad! I had 120v power going...

I have a issue when I’m recording my electrical readings with the Fieldpiece SC680.
When I’m trying to generate a report for my electrical readings on a Single Phase Condenser Unit it will say...

That makes since! Because this home seem very insulated and tight as far as they have good windows around the house. The homeowner has the thermostat set at 73 degrees!!😮 and it maintained that temp...

Hello

I just installed a 2 1/2 ton 13 SEER Concord Condenser Unit and I make sure that I commission all my new installs by using my Fieldpiece Joblink probes along with my Fieldpiece SC680...

I was just watching a video on the new Supco Lineset Tool cleaning kit and was wondering if anyone used it yet and if it’s worth purchasing?

Thanks

I got a callback from Fieldpiece this morning and I was basically told the same thing that they are aware of the issues and they are trying to have it all together by Tuesday. I was having trouble...

Well I was just testing it out and all of my probes will not link up to the App! I tried installing and re-installing it and I’m getting the same results.

Yes I understand that but this new update has knocked out all my previous jobs info I done saved.

Yes no problem!
I’m really not feeling it so far but I’m a creature of habit and they’ve done away with the colored bar and everything and the reason I like the older version was the ease of using...

They just updated the Joblink app and it SUCKS!!!
All my records from previous jobs are missing and the graphics sucks!
Just wondering if anybody else is having these issues?

Thank You!
As soon as I press reply I got to thinking “Maybe I should be calculating the Output” and lord and behold that’s what I needed to do! And plus I know I needed to adjust that Gas Valve...

The output- 72,000 BTU.

Static Pressure Testing Spots- Drilled a hole on the top of the furnace before the A-coil and condensate pan and drilled a hole in the inside cover with the pitot tip aimed...

Hello I have a question is using the old rule of thumb of getting the furnace operating CFM’s is obsolete now since we all go by the manufacturers blower motor chart and the static pressure that the...

Yes but I’m going back over there this weekend to do the process all over again and I will comeback on here and let you know how it went. Thank you so much for taking time out of your evening to help...

It’s a new install

Yes sir

It’s new equipment but I had to add a 5/8 x 3/4 bushing in order to connect to the 3/4 case coil.

200 psi

Ok Thanks!
I’m having a issue (I think) with my new Fieldpiece Micron MG44 Micron Gauge because I just did a install and I leak check the system and pressurized the system and let it sit for about...

How low do your micron gauge suppose to read to let you know it’s operating properly? Oh and thanks for the reply! 😁

Hello,

I wanted to know how do you test a Vacuum Pump to make sure it’s operating correctly? And how often do you test it?


Thanks!

It does now but when I connected one set to take my ESP and the other pair to get my Gas Pressure reading I noticed when I zeroed out one of my probes it zeroed out the other one at the same time but...

Hello,

I have the Fieldpiece Joblink App and I noticed that on the Manometer Section of the App it seems like you can take up to 4 different static pressure readings including gas pressures at the...

Thanks for the information! I went on YouTube and I noticed that the firmware update was already in Tools and mines was not when I tried to update mines. Do I have to contact Fieldpiece so the can...

Hello

Is anyone out here having issues with the Joblink3 App putting the correct Metering Device on their reports? IÂ’ve been having issues when I enter in what metering device the system has on...

I believe that’s the case because I have the Joblink3 App and when I went to my Tool Manager it let me know there was new Firmware available for the Psychrometer Probes and I just updated mines. So I...

Man that’s great!!
I was thinking that I had to buy some more probes! 😁

I didn’t see a release date for them I was just wondering are they out yet since I stay in the Midwest and to me we seem like the last ones to get the new stuff! 😂

Hello

I just got a Email from Fieldpiece about the new High Temp Psychrometers that can measure up to 250 degrees! Wanted to know if anyone is aware of this?

Thanks!

Well I made sure I turn the power off and I took the motor leads off the control board and went to common to ground and my meter made the beeping sound and showed continuity and I went down the line...

Thank you for the response!
I was worried for a minute that I spent a lot of money on a meter that was defective! And I for got to add that I did test the end coming current to the motor and I was...

Hello

I have the Fieldpiece SC680 Multi Meter and I was wondering does anyone have any problems when they ohm out motors for continuity or resistance? I had ohm out a motor one day and it was a 3...

So basically 0.5 will be the benchmark and until you add up all the component pressure drops and subtract that from the 0.5 to get the available static pressure then we will use that number to set my...

Yes it does thank you so much!

I totally agree and thanks I would think we would try to set it in the middle.

I was learning about how to get the friction rate and how to calculate in order to do ductwork design. I know that you need the Manual J to actually get the information I need to begin to design the...

Hello and thanks I was just trying to make sure! Thanks!

Hello I’m trying to see if I’m on the right path when it comes to getting the maximum operating (ESP) External Static Pressure on the new ECM Furnaces compared to the old PSC motors.

When it...

Hello I I have the Fieldpiece Joblink App that I’m using to get my Electrical reading by using the SC660 meter and I wanted to know how do you use that data to compare it to the clients energy bill...

Wow thanks for that info!! I’ve been *****ing and moaning about those short gator clips and that’s all you had to do! 🤪