Type: Posts; User: controltec
Search: Search took 0.01 seconds.
You've got mail. I sent you a link to download all that I have. If you need any help let me know!
sure we use a ASD driver for this. Works really well. We have probably integrate over 50 sites like this. The driver will also allow you to still use the PSI software and tunnel down through the...
I sent you an email with a download link.
I sent you a link for a download of all that I have.
01-31-2013, 09:03 AM
You have solidified my point. You have yet again wasted everyone's time including your own to post something that completely meaningless. I must have missed something big in the...
01-31-2013, 08:57 AM
If you email me from my email in my profile I will send you a link to download all the stuff that I have.
01-30-2013, 05:34 PM
01-30-2013, 05:01 PM
I really don't know why you would waste your time or anyone else's time to respond to a forum and not contribute anything of value. For your information I copied this right out of the user manual,...
01-30-2013, 12:10 PM
the GCM is the Global Control Module. this is the master brain behind a network 8k system. This you can access with hyperterminal or XPSI software. The XPSI is in the download that I sent you. ...
01-29-2013, 06:31 PM
I will email you a link to download the manuals that I have. You don't need any special software for the LCM's they are just a RS-232 interface with hyperterminal. If the LCM isn't...
hyperterminal settings will vary depending on what was setup in the GCM. Usually 8 none and 1 with a 9600 baud works just fine. You will need a 9 to 25 pin serial cable. Depending on the type of...
01-21-2013, 09:23 PM
you've got mail. Let me know if you need any help.
You've got mail. Feel free to call me if you need anything.
01-21-2013, 08:30 AM
I sent you an email with a link for the manuals that I have. If you need any help just give me a call.
I can email you a link to download all that you will need for manuals. Since you don't have an email in your profile please send me an email from my profile address. If you need any help give us a...
12-30-2012, 01:59 PM
I just sent you an email with a link to download what you need. If you have any questions contact me and I'll see how I can help you.
I sent you a link in your email with all the stuff that you will need. Let me know if you need anymore help. We specialize in integrating these system into Niagara AX.
Text065 and USC Anteater
my email is in my profile. If you shoot me an email I will send you a dropbox link to download all that you will need.
06-25-2012, 08:56 PM
If you have a MN-ASDI you have micronet VAV controllers and these do not talk on the ASD bus. The MN-ASDI is the integrator that translates between U-bus and ASD to get the information up into the...
06-04-2012, 10:54 PM
one more thing.... in the GCM you will see the EMS points for the MZ labeled as AIN1, AIN2....DIN1, DIN2....etc. On the smartware drawings the actual GCM block is the MZ2 and the points like AIN1...
06-04-2012, 10:51 PM
The information passing between a MZ2 and GCM will happen through the EMS block. You have a total of 8 AI and 8 DI to be able to pass from the GCM to the MZ. If there is logic in the GCM you can...
cwellsra I just sent you an email with a link to download the documentation that you requested. Let me know if you need any help!
05-29-2012, 09:42 AM
I'm using a B&B model USOPTL4
have had really good luck with this working on WIN7 with the newest 4.0 XPSI. We also will use this...
Cal1 I sent you an email with the GCM manual. I don't have a copy of the PEM manual.
Results 1 to 25 of 51