Search:

Type: Posts; User: rikenz

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    2,940

    I just finished installing a Pelican System...

    I just finished installing a Pelican System including 25 water-source heat-pumps and a cooling tower/ circ pump core system. Everything is working great and the interface is simple and has everything...
  2. Replies
    1
    Views
    446

    srf64, I've been doing HVAC and Controls for...

    srf64,
    I've been doing HVAC and Controls for over 20 years and just installed a Pelican Wireless System on a building with 25 water source heat-pumps and a cooling tower/ circ pump core system....
  3. Replies
    1
    Views
    217

    You need to set the dip switches on the...

    You need to set the dip switches on the controllers. Make a list and label them all so that when you do a discovery on the supervisor you know what you're looking at.
  4. Replies
    4
    Views
    325

    The latest version of PCT configuration software...

    The latest version of PCT configuration software for the field controllers allows you to set communication protocol to Bacnet or N2.
  5. Replies
    2
    Views
    382

    Be sure to do a database repair once in awhile....

    Be sure to do a database repair once in awhile. This seems to cause strange problems if not maintained properly.
  6. I would call AIC Wireless at 408.988.5331 because...

    I would call AIC Wireless at 408.988.5331 because I'm guessing this is their product branded by Wattstopper http://www.aic-wireless.com/category/products/transceivers/

    Also before bringing the...
  7. Replies
    18
    Views
    663

    The controller might be programmed for a...

    The controller might be programmed for a different sensor. Do you have HVAC-Pro?
    From the manual it looks like the possibilities are:

    Nickel Sensor Temperature Sensor: 1000-ohm thin-film nickel...
  8. Replies
    172
    Views
    42,434

    Does it use the same software?

    Does it use the same software?
  9. Replies
    172
    Views
    42,434

    I noticed the service tool has Bacnet in its file...

    I noticed the service tool has Bacnet in its file name. Do you know if a different service tool is used for a LON system?

    Thank you!
  10. Do you know if you can program a Lynxspring/...

    Do you know if you can program a Lynxspring/ Honeywell/ Easyi/o or whatever other branded JACE with JCI's FX workbench?

    I've never tried this but I've heard that it works??

    Thank you!
  11. Replies
    3
    Views
    819

    Depending on the type of "web profile" you've...

    Depending on the type of "web profile" you've been set up with you may not see the workbench tree on the left hand side of the screen.
  12. Replies
    7
    Views
    677

    Is this the DBACS gateway you all are talking...

    Is this the DBACS gateway you all are talking about? I have a job about to start with three of them. This is a LON system.
  13. Replies
    42
    Views
    3,664

    I would highly recommend staying away from the...

    I would highly recommend staying away from the JCI Metasys line and moving into the JCI Tridium Niagara JACE. The existing system also sounds like a good candidate for integration. You would leave in...
  14. Replies
    15
    Views
    2,303

    I've met the Easy I/O people and they are very...

    I've met the Easy I/O people and they are very knowledgeable and passionate about their product. I use JCI branded JACE's due to my supply chain and have no complaints. If you are integrating old...
  15. Replies
    44
    Views
    4,427

    It depends on many factors but it sounds like you...

    It depends on many factors but it sounds like you may be best starting over. When you install a new system be sure to insist on an "open" system, I would use Tridium Niagara with whatever branding...
  16. Replies
    299
    Views
    36,966

    Thanks for the attachment tridiumtech, this...

    Thanks for the attachment tridiumtech, this clearly shows the power of Tridium.
  17. Replies
    10
    Views
    1,435

    It's nice to find a company that will fund your...

    It's nice to find a company that will fund your controls education but you will probably take a hit in pay starting out.
    I took a Metasys N2 class from a local vendor then went home, bought a bunch...
  18. Replies
    3
    Views
    604

    Ha! Hilarious! Good point.

    Ha! Hilarious!

    Good point.
  19. Replies
    3
    Views
    604

    Are you onsite? The building that I have with a...

    Are you onsite? The building that I have with a DX has all the points written down on little points sheets on the inside of the drop down door on the front cover of the DX. What I actually did though...
  20. Replies
    299
    Views
    36,966

    Control$- I agree. Often it seems like we hate a...

    Control$-
    I agree. Often it seems like we hate a system because we don't know how to use it and love a system because we do. I can think of some really frustrating integrations I've done with field...
  21. Replies
    299
    Views
    36,966

    Ha! This thread is hilarious, goes on for DAYS!...

    Ha! This thread is hilarious, goes on for DAYS! I'm a Tridium guy and still wish they'd get their java **** together. But the things the box can do..... 10 years ago this was but a dream.
  22. Replies
    5
    Views
    691

    Geo- More information would be helpful for us to...

    Geo-
    More information would be helpful for us to make recommendations.
    Are you a controls contractor?
    What systems are you trained in?
    What is the system that you are interested in changing out?...
  23. Replies
    69
    Views
    4,700

    Working for a union shop in San Francisco maybe...

    Working for a union shop in San Francisco maybe 15 years ago the rule was you were on the clock from your first stop in the morning to your last stop at the end of the day. The commute in to the...
  24. Thread: Economizers

    by rikenz
    Replies
    5
    Views
    1,023

    I found this helpful. ...

    I found this helpful.

    https://customer.honeywell.com/resources/techlit/TechLitDocuments/63-0000s/63-8594.pdf
  25. Replies
    29
    Views
    5,499

    I have mine set up as DaveCR and it's working...

    I have mine set up as DaveCR and it's working good.
    You need to add an Email Service if you don't have one already
    Set up an Email Recipient
    Then set up the Outgoing Account as DaveCR has...
  26. Thanks again wbrown!

    Thanks again wbrown!
  27. Replies
    3
    Views
    867

    I've always done this with XPSI. Do you have this...

    I've always done this with XPSI. Do you have this program?
  28. Thank you, Daikin came through yesterday and...

    Thank you, Daikin came through yesterday and emailed me the pdf. They did however say that it was Tridium who was supposed to provide this information.

    R
  29. Niagara AX Mcquay OPM Driver Open Protocol Data Information Packet

    Hello,
    I have a Mcquay RFS135CLY Rooftop Air Handler that I'm trying to integrate into Niagara AX. I have a JACE with the Mcquay OPM driver and I'm setting up the station. As points needs to be...
  30. Replies
    1
    Views
    490

    [QUOTE=t-reck;17564591]Does anyone have a hex...

    [QUOTE=t-reck;17564591]Does anyone have a hex code table for the McQuay OPM data for WSHPs? I'm migrating the system from using a JCI MIG in between a Jace and the OPM. The HPs have microtech-I...
  31. Replies
    8
    Views
    714

    I'm sure you've done this but right click on the...

    I'm sure you've done this but right click on the MSTP port in the tree and make sure it's enabled. I spent an hour one time trying to figure out why I wasn't communicating and BINGO. As this was a...
  32. Thread: Cheap Training?

    by rikenz
    Replies
    13
    Views
    1,488

    RSD Total Control has Metasys and Niagara based...

    RSD Total Control has Metasys and Niagara based classes in San Jose and Sacramento. Classes are good, really condensed over 3 days, a good start. If you don't currently have any control systems you...
  33. Replies
    4
    Views
    1,185

    I like the Acromag RS-485 repeater. Seems like a...

    I like the Acromag RS-485 repeater. Seems like a well made unit.
  34. Thread: Cheap Training?

    by rikenz
    Replies
    13
    Views
    1,488

    Where do you live?

    Where do you live?
  35. Replies
    11
    Views
    1,473

    I figured it out. Changing Maximum Global...

    I figured it out.
    Changing Maximum Global Override Time
    Station/config/sysinfo add facets: maxOverrideDuration/Reltime/3hrs- or whatever you want max to be
    just write in maxOverrideDuration as...
  36. Replies
    11
    Views
    1,473

    CB, Can you walk me through how to do this...

    CB,
    Can you walk me through how to do this globally? I tried to follow the Niagara Central post but was not successful.

    Thank you!

    Sean
  37. Replies
    29
    Views
    5,499

    I would love a copy of this as I've yet to get it...

    I would love a copy of this as I've yet to get it to work...
    My email is in my profile. Thank you!

    R
  38. Replies
    23
    Views
    2,465

    Cagey57- Thank you for the correction. I just...

    Cagey57- Thank you for the correction. I just read through the N2 Communications Bus Technical Bulliten Lit# LIT-636018

    On page 19 it states :
    "Figure 5 shows an NCU in the middle of the single...
  39. Replies
    23
    Views
    2,465

    If you have two trunks going off in two...

    If you have two trunks going off in two directions with an End Of Line setting at the the two ends you have two n2 trunks and need to hook them up to two separate RS-485 connections on the FX60. It...
  40. Replies
    23
    Views
    2,465

    Each FX-60 that you install will come with an N2...

    Each FX-60 that you install will come with an N2 driver and embedded workbench. You can do whatever you want with the existing station on the unit.

    With embedded workbench you cannot create a new...
  41. Replies
    28
    Views
    5,691

    Where are you located? I'm sure there are a...

    Where are you located? I'm sure there are a number of people on this site that can help you out. Tridium Niagara is a widely used platform that your contractor must not be accustomed to. DGlux is a...
  42. Replies
    19
    Views
    2,830

    It worked! Wow what a great tool! Thank you! I...

    It worked! Wow what a great tool! Thank you!
    I had to set the UDP port to 47808 as it wouldn't let me enter 0xBAC0 into PCT for some reason. I also had to set my network number to 2 which is the...
  43. Replies
    12
    Views
    2,080

    Yes

    Yes
  44. Replies
    12
    Views
    2,080

    I'm still trying to make this work. Is there a...

    I'm still trying to make this work. Is there a place in the manual with the configuration parameters needed?
  45. Replies
    19
    Views
    2,830

    Can anyone walk me through how to do this?

    Can anyone walk me through how to do this?
  46. Replies
    33
    Views
    3,578

    Thanks guys, I'm taking your advice on this and...

    Thanks guys, I'm taking your advice on this and going the Rover route. I contacted Echelon and the sales guy in reference to my question
    "Do you know if I can use this software to configure Trane...
  47. Replies
    33
    Views
    3,578

    Thanks Dapper! I'm new to Trane LON and trying to...

    Thanks Dapper! I'm new to Trane LON and trying to figure this all out. Check out this link https://www.echelon.com/products/tools/integration/lns-plugins/pluginShow.asp?pluginManID=61
    It shows a...
  48. Replies
    33
    Views
    3,578

    "You can however use any of these software...

    "You can however use any of these software packages to configure Trane comm 5 controllers.[/QUOTE]"

    Dapper,
    Is this true? If I purchase Lonmaker and install the Trane LNS Plugins can I configure...
  49. Replies
    10
    Views
    957

    How do you "open the platform of your local...

    How do you "open the platform of your local machine"?
    I haven't tried this.

    Thanks!
  50. I use it all the time and love it.

    I use it all the time and love it.
Results 1 to 50 of 136
Page 1 of 3 1 2 3

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards