Search:

Type: Posts; User: megohm

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    556

    Pipe Wrench

    I feel your grief Overhaul.. We had a incident where a no name company felt it was in the chillers best interest to get a 24" pipe wrench and put it on the cuppling of a centrifical compressor when...
  2. Replies
    16
    Views
    2,760

    Thanks for your help..

    Thanks for your help..
  3. Replies
    16
    Views
    2,760

    YCIV

    I have the manual for the ycav vfd it should apply to the yciv. My e-mail is travlnsurfer@hotmail.com. I've tried to find the service and troubleshooting guide for this chiller but no luck not even...
  4. Replies
    16
    Views
    2,760

    M #

    Yciv0267sa46vabb w/ a mts45sadd46/200 comp
  5. Replies
    12
    Views
    2,386

    YCIV Vibrations

    We have been cutting out the section of pipe at the discharge and placing the discharge transducer at the out let of the oil seperator.
  6. Replies
    16
    Views
    2,760

    Service Manual

    Dose any one have the service lirature on this series machine. I have the iom but I need the service litrature info. Any help would be greatly appriciated.
  7. Replies
    26
    Views
    2,460

    Do you mean the brass body style with the four...

    Do you mean the brass body style with the four bolts to hold the cover on.
  8. Thread: York Oil

    by megohm
    Replies
    23
    Views
    7,940

    E Oil

    What machine is the E-oil used in?
  9. Replies
    26
    Views
    2,460

    I have had a couple of the clam style where every...

    I have had a couple of the clam style where every thing looked as tho it was opening and closing but it really was'nt, the feed back to the display would show 0% and 100%, the board would show the...
  10. Replies
    26
    Views
    2,460

    Style EXV

    What style EXV is it is it the brass body style or the newer sportland style exv. Carrier has had alot of problems with the float on those machines on the newer style series 6 they whent with a plate...
  11. Replies
    17
    Views
    1,157

    More Pics

    More Pics
  12. Replies
    17
    Views
    1,157

    The Pics I promised

    Kind of late but I have had my hands full. The company that did this job did a sweet install. I have to post the rest in a seperate post.
  13. Replies
    46
    Views
    4,268

    Its a super thermo bob.

    Its a super thermo bob.
  14. Thread: CVHF

    by megohm
    Replies
    40
    Views
    2,373

    Everyone seems to have really good ideas , I had...

    Everyone seems to have really good ideas , I had the old style gasketts on a economizer that I just replaced I used vac grease on the gasketts no leaks and the unit pulled down to 250 microns lowest...
  15. Thread: Guide Vanes

    by megohm
    Replies
    16
    Views
    1,106

    Guide Vanes

    On a chiller with a VSD what is the determining factor that opens up the guide vanes. I've been told that the the factory dosnt even tell the factory mechanic this detail but I do'nt belive it....
  16. Replies
    153
    Views
    34,603

    Y-delta

    Y-delta
  17. Replies
    153
    Views
    34,603

    I cleaned the winding thermistors at the...

    I cleaned the winding thermistors at the compressor, like you suggested york 56 and I checked the settings at the compressor amprage settings were 168 at 105% but for a 180 ton machine it should be...
  18. Replies
    10
    Views
    1,762

    Carrier had a bullitien on this series chiller...

    Carrier had a bullitien on this series chiller and its coils leaking at the u-bends and on the surface area of the coil as well.
  19. Replies
    17
    Views
    1,157

    Not really cheap I believe that these machines...

    Not really cheap I believe that these machines were not ready for the cold water temps that the newer Yorks can handle. This series machine was desined in the era of 85 in and 95 out not 65 in and 72...
  20. Replies
    153
    Views
    34,603

    YCAS Low current/MP/HP

    I have read most of the posts on this series machine but it seems that no one has really provided a perminant solution to the problem. The problem we have on these machines was occuring forever one...
  21. Replies
    17
    Views
    1,157

    Hey turbo master send me some info to my e-mail...

    Hey turbo master send me some info to my e-mail if you got it travlnsurfer@hotmail.com
  22. Thread: McQuay Software

    by megohm
    Replies
    3
    Views
    1,322

    5629081920 DMG parts.

    5629081920 DMG parts.
  23. Replies
    17
    Views
    1,157

    Carrier 19EX4343836DN

    I have a Carrier 19EX4343836 with a 02EXB836 compressor. The chiller has oil loss problems and a ready oil management system has been installed into the the chillers system to possibly assist in...
  24. Replies
    1
    Views
    525

    Bearing Failures On VSD Motors

    What have you done to reduce or eliminate the failures othor than the inductor mods on York chillers and othor machines?
  25. Replies
    31
    Views
    5,657

    Bearing Bullitiens

    Abserbertek if you still have those bullities on the brushes retro I would greatly appriciate them.
Results 1 to 25 of 81
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image