Type: Posts; User: tcape

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. head room

    The unit has a counter built on top of it, but I think I can slide it out and take the top off, I think the water and drain are connected with flexible tubing.

    Thanks for the info!
  2. 20 yr old Hoshizaki F250-BAE flaker- gray ice and has anybody ever replaced...

    The mechanical seal and o rings?

    Called tech support today after the customer called and said their ice maker was making a funny noise and had not made any ice all night. I told them to unplug it...
  3. Mission completed! What a pain in the butt! After...

    Mission completed! What a pain in the butt! After I finally got the flat top griddle unstuck from the frame it was on and vacuumed up the burnt crap I was able to see where the temp probe went into...
  4. I have the gas control valve already

    The model number really doesn't matter now, when I talked to Royal they gave me the info I needed to get the right part, I verified it by visual observation and now I just need to know how to access...
  5. Royal Range need to replace oven control, questions

    Has anybody done this before? This is a flat top on the left side with a conventional oven and a stove on the right side with a convection oven. Sorry, no model number, and I called Royal when I was...
  6. starting with head off

    I was thinking about doing that, but didn't....didn't know if it would hurt anything or not....Thanks for the info!!
  7. I replaced the valve plate and that fixed it,...

    I replaced the valve plate and that fixed it, works fine and 100% quieter. Could not see any actual broken parts.
  8. Copeland K Body compressor excessive vibration

    Compressor model number KAJB-010E-CAV-100.

    Customer calls the other day and says the walk in freezer is making a lot of noise. I get there and it seems to be vibrating excessively. The front right...
  9. Update- got the proper type tubing for the pumps...

    Update- got the proper type tubing for the pumps and then used poly tubing to go to the containers and dishwasher. Now I have no back feeding. looks like the surgical type tubing acts as a check...
  10. Update- After stopping over this afternoon I...

    Update- After stopping over this afternoon I discovered the following:
    There is nothing connected to the pumps.

    I ran new tubing from the detergent pump to the lower rear connector and into the...
  11. Hobart LX30 dishwasher- chemical feed problem

    Customer calls and says the chemicals don't feed, in fact the water from the dw is going into the containers. I stop over to look and there is no PRV. I tell the customer to have whoever hooked up...
  12. Used Kysor multi deck cases- I need to identify model to install properly

    A small grocery store(owned by people from a foreign country) bought 3-12 foot used sections and they want me to put them together and get a condensing unit for them. I told them I need a model...
  13. Replies

    Thanks so much for the information, it was...

    Thanks so much for the information, it was extremely educational. I knew the basics about these kinds of controls, but your info has added to my knowledge!

    Thanks again,

  14. Replies

    Here is a short video of the burner, and I have...

    Here is a short video of the burner, and I have it turned up to 500. The oven was not running at all prior to me arriving so the only heat in the oven was from the pilot light....
  15. Replies


    The oven was working fine a few months ago and all the top six burners burn fine. I did take a short video of it, but I don't have time to post it right now.. maybe in the AM. But the flames barely...
  16. Replies

    Vulcan 36L Oven control?

    I have a Vulcan 6 burner stove with oven and I'm having trouble with a low flame in the oven and it takes forever obviously to bake anything. This is NOT a convection oven. I'm making the assumption...
  17. Got the new plug today and Voila! it works!

    Got the new plug today and Voila! it works!
  18. Ruud Commercial gas pack 7.5t RKNL- factory miswiring?

    Went to start up the AC on a unit unit I installed last November and it would not come on. I had 24 volts leaving the unit and heading toward the economizer, but that was not installed. The jumper...
  19. Replies

    Just emailed them, they are sending me the wiring diagram

  20. Replies

    Funny how we are having similar problem with R22...

    Funny how we are having similar problem with R22 as we are with 22LR
  21. Replies

    Need wiring diagram/shotgun for True T-24GC

    Correction- TRUE-The evap fan is not running and it killed the compressor. There is no power to the evap fan and I need to find and verify any components that break the fan circuit. I can't believe...
  22. I truly appreciate your input, thanks for taking...

    I truly appreciate your input, thanks for taking the time to reply. This machine is approximately 10 years old. I agree Hobart stuff seems to be around forever, but it would be nice to have a...
  23. Hobart AM-14 Dishwasher Motor- alternatives to Hobart?

    I have a customer that has an AM14 Dishwasher and some stuff I work on and other stuff I let Hobart do it. Their pump motor is in the process of dying and I told them to call Hobart, because They...
  24. What I figured

    I was thinking it would be something like that.... oh well... the machine is almost 20 years old... time for a new one.
  25. Hoshizaki KM-800MRE- evaporator tubing seperating from cube grid?

    I have a Hoshizaki ice machine that seems to be flooding the compressor. Can someone tell me how the evaporator tubing is attached to the stainless steel cube surface? It appears as though the "cube...
Results 1 to 25 of 279
Page 1 of 12 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event