Search:

Type: Posts; User: 19C

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    1,347

    Sounds like the discharge reed valves are gone,...

    Sounds like the discharge reed valves are gone, refrigerant gas goes back and forth between the piston chamber ant the discharge head space and over heating the head.
  2. Good deal Cpeck. Thank's for the feed back....

    Good deal Cpeck. Thank's for the feed back. Sometimes these comm problems can drive people nuts.Speaking of going nuts, time to start the weekend.:couch:
  3. Thread: help YK

    by 19C
    Replies
    1
    Views
    405

    O la servicetrane. Did you change the whole vsd...

    O la servicetrane. Did you change the whole vsd or did you changed just one phase module ? One time I changed just one phase module and over look a fuse that was blown down stream of the disconnect...
  4. Hi Cperk. I have good luck with Keyspan usa 19HS...

    Hi Cperk. I have good luck with Keyspan usa 19HS and Belkin F5U409-CU usb to serial converters. Smardt recommends the Belkin to connect to the Turbocor's comp's. Never had problems connecting to...
  5. Thread: Training budgets

    by 19C
    Replies
    25
    Views
    1,829

    Hi ChillerGuy81. The times I have been to York...

    Hi ChillerGuy81. The times I have been to York Pa.What a nice state people are good ,friendly. Big rat race here in Cali. Bay area worse. When I have to work Bay Area drive times easy hit 4 to5 hours...
  6. Thread: Training budgets

    by 19C
    Replies
    25
    Views
    1,829

    Hi Duke. We get our share of call backs. The...

    Hi Duke. We get our share of call backs. The bosses are cool. If we need help no big deal they do their best to get us what we need. We make some mistakes and so long as we learn from them the bosses...
  7. Thread: Training budgets

    by 19C
    Replies
    25
    Views
    1,829

    Several Junior Techs have left after going to...

    Several Junior Techs have left after going to some classes,I think they didn't like chiller work,o-well. Lot of in house training on tear downs/regaskits,control panel retro,
    Turbocor retro,Smardt...
  8. Thread: Training budgets

    by 19C
    Replies
    25
    Views
    1,829

    Company I work for has sent at least 2 people if...

    Company I work for has sent at least 2 people if not more to these classes, Factory Trane-RTHA/B/C & ABS, factory Carrier 19xr,30gx/hx, factory York yt/yk/ys/vsd/viper/laditude,Entech panel...
  9. Thread: RTAA340

    by 19C
    Replies
    19
    Views
    1,261

    Hi Chiller123. You may have done this already, I...

    Hi Chiller123. You may have done this already, I did a start up on new RTAA long time ago and the load/unload soli:couch:noids where wired backwards from the factory,check wiring? good luck...
  10. Replies
    9
    Views
    1,456

    I think Turbocor retrofit compressors can only be...

    I think Turbocor retrofit compressors can only be purchase by Smardt Retrofit Solutions and Mag Lev here in the USA.Danfloss didn't want to deal with all the contractors.Call them for local...
  11. 1-Could have been bad from the factory, try...

    1-Could have been bad from the factory, try getting a warranty.
    2-Check that they gave you the correct compressor,voltages,models,etc
    3-Check wiring and for correct phasing.
    4-Check discharge and...
  12. Replies
    13
    Views
    1,070

    Yea the good old days, before recovery...

    Yea the good old days, before recovery gear!:CU::CU::CU:
  13. Thread: 19xl

    by 19C
    Replies
    44
    Views
    6,395

    retro 19xl

    looked at the pic's of the conversion, nice job rob man!!! congrats on the newest chiller member!!!!!!! did you have to tweak the values on the kiltech panel much for start up? how much oil did...
  14. Replies
    20
    Views
    1,874

    Mistor Quest

    WELCOME TO THE DARK SIDE. YOU WILL KNOW THE ANSWER,AFTER YOU
    HAVE GONE TO THE NEXT SERVICE MEETING IN SACRAMENTO. WELCOME
    AGAIN. CHILLER ROB TRAINED. :p
Results 1 to 14 of 32
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event