Search:

Type: Posts; User: emtim

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Ddc retofit

    by emtim
    Replies
    1
    Views
    203

    Do companies typically leave a schematic . I have...

    Do companies typically leave a schematic . I have seen rooftops converted with schematics , p
  2. Thread: Ddc retofit

    by emtim
    Replies
    1
    Views
    203

    Ddc retofit

    Hello I have some building with what I call a hybrid system for controlled carrier service tool 5 with a combination of pneumatics . We have a installer in our area who installed this ....
  3. Thread: Fan blade stuck

    by emtim
    Replies
    32
    Views
    1,404

    I will usually order new blade, cap .i will check...

    I will usually order new blade, cap .i will check availability ,have had some odd motor blade combinations ,especially with York and trane .i had a old trane from 1960 .the blade was a airplane...
  4. Replies
    13
    Views
    913

    Voyager

    Did you get it running. Been a while in think the draft inducer motor starts first and then the igniter lights .Proves flame and gas valve opens . Keep us posted .
  5. Replies
    13
    Views
    913

    Voyager

    Have you put in test mode and if so what happens .
  6. Thread: System pilot

    by emtim
    Replies
    5
    Views
    484

    The rtu was at idle .

    The rtu was at idle .
  7. Thread: System pilot

    by emtim
    Replies
    5
    Views
    484

    System pilot

    Went on a call today with a system pilot and had no heat .checked zones and when I attached the zone to the system pilot on the bottom of screen it said disabled for every zone. I would normally see...
  8. Replies
    8
    Views
    829

    Did you try grainger, not a big fan of dayton . I...

    Did you try grainger, not a big fan of dayton . I usually go to a few motor shops ,what is wrong with the original motor maybe you can get it rebuilt.
  9. Thread: Lennox NAS

    by emtim
    Replies
    139
    Views
    32,736

    Glad you made it out .I was out of springfield...

    Glad you made it out .I was out of springfield ,ma .When we were aquired from tradewinds there were 4 techs and a manager. Two were laid off ,two left and manager left in one year. I remember ...
  10. Thread: national grid

    by emtim
    Replies
    0
    Views
    250

    national grid

    Has anybody worked for them or no anybody who has . I appiled and taken test ,interview .possible career change . Service rep B ,Thanks Rick i
  11. Replies
    59
    Views
    5,185

    serta i comfort prodigy ,three models to choose...

    serta i comfort prodigy ,three models to choose from ,last bed I purchased had a matress with with foam ,felt nice at store hated it,my wife would say meet you in the middle .The serta i confort has...
  12. Thread: bristol dx

    by emtim
    Replies
    4
    Views
    680

    thanks this does have a direct vent kit .Working...

    thanks this does have a direct vent kit .Working good .
  13. Thread: bristol dx

    by emtim
    Replies
    4
    Views
    680

    All fixed ,Found b vent on termination fitting...

    All fixed ,Found b vent on termination fitting not sealed properly ,allowing exhaust and fresh air to mix ,starving out fire ,it is running and the sit control is beeping ,warranty covering this...
  14. Replies
    31
    Views
    2,123

    I think these are the old york sunshine series...

    I think these are the old york sunshine series ,the panels all interlock on each other ,is the condenser fan grill on top and its along rectangular grill. Is this electric heat ,had some of these at...
  15. Replies
    4
    Views
    731

    I too was having issues ,does this have a...

    I too was having issues ,does this have a ignition control ,I have a fireplace control made by sit ,the tech I was talking to states it has a timing mechanism (runs 6 hours ) .This is a built in...
  16. Replies
    22
    Views
    1,657

    what kind of issue you having with unit , I had...

    what kind of issue you having with unit , I had one giving me problems it was heat exchanger ,new exchanger replaces the one inshot burner design.
  17. Thread: bristol dx

    by emtim
    Replies
    4
    Views
    680

    venting

    I am using simpson direct vent , I have checked literature on this and do you seal the fittings ,these are a twist lock fitting . I have read that these stoves are sealed units and if the pipes leak...
  18. Thread: bristol dx

    by emtim
    Replies
    4
    Views
    680

    bristol dx

    Hello just bought a bristol dx by hearthstone , install went good ,upon lighting did not work ,The stove now does run longer after i checked log placement ,checked pressure before valve . The stove...
  19. Replies
    6
    Views
    923

    fan limit control

    Just installed a thermo pride oil furnace ,what settings do you set up for the on and off on the fan control ,installed late last night ,going back to finish later in week ,heavy furnace, Thanks
  20. Thread: Winter Gear

    by emtim
    Replies
    24
    Views
    1,865

    winter gear

    Depends on what i am doing ,layers ,if outside all day and its colder 20 degrees and colder with wind i will switch to insulated coveralls . I have a insulted hat with full face mask ,insulated snow...
  21. Replies
    2
    Views
    593

    Has anyone ever worked on one of these . There is...

    Has anyone ever worked on one of these . There is a switch on controller auto and manuall. I have never seen one .Thanks
  22. Thread: posts

    by emtim
    Replies
    2
    Views
    480

    posts

    I posted some posts how do i move them into the tech to tech commercial.Thanks Rick
  23. Replies
    8
    Views
    1,032

    I have seen theses installs , you could have...

    I have seen theses installs , you could have electrical come out of roof .I had one we rerouted and had a pitch pocket for electrical and unit still leaked covered up rtu and shut off it was the roof...
  24. Thread: pump

    by emtim
    Replies
    6
    Views
    718

    pump

    I have to replace bearing assemblies on gthis pump ,two on site , have not done any in a while .1 do you guys reuse impeller or should I order new ones . 2 These pumps do have isolation valves ,is...
  25. Replies
    2
    Views
    593

    diaphragm controller

    Hello ran across this yesterday ,no heat call after researching found out on a call for heat this energizes coil in this controller and releases gas into pilot ,then the main gas valve opens .Does...
Results 1 to 25 of 115
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event