Search:

Type: Posts; User: tom9146

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    805

    im new at the service end of things,but the way...

    im new at the service end of things,but the way we do it is x amount to check all units (drains freon ect)and if there are mechanical defects we go into a predetermined hourly rate (time and...
  2. Replies
    13
    Views
    1,122

    not promoting ebay but you can get some good...

    not promoting ebay but you can get some good buys,and at least you can set the price and see if they go for it.if your just starting off its not easy i ve spent over 100000 on sheet metal equipment...
  3. Replies
    6
    Views
    892

    trying to find out what terminals i will have 24...

    trying to find out what terminals i will have 24 volts at.have 24 at r,can jump r to g and fan kicks on r to y cond kicks on r to w and isolation relay clicks but no burner jump t/t on primary...
  4. Replies
    6
    Views
    892

    thanks for the help,why even bother saying...

    thanks for the help,why even bother saying anything?
  5. Replies
    6
    Views
    892

    have a rudd oil furnace that is not working...

    have a rudd oil furnace that is not working propery,first i replaced the fan center but it still is not fixed,when i call for heat the isolation relay clicks but the burner does not start,second the...
  6. Replies
    24
    Views
    5,037

    what sq ft is your house and what the location?...

    what sq ft is your house and what the location? something seems strage
  7. Replies
    4
    Views
    1,580

    thank you for the "payable within 10 days of...

    thank you for the "payable within 10 days of invoice receit"i will include that on my proposals/invoices.on the topic of the progressive draw payments could you explian that a little better?
  8. Replies
    4
    Views
    1,580

    i was curious if any contrctors have a...

    i was curious if any contrctors have a frustrating time getting paid from general contractors or home owners?what upsets me is say a 10k job on a new house,install a furnace and ductwork with...
  9. Replies
    2
    Views
    683

    i was looking for some prefab rectangle duct, i...

    i was looking for some prefab rectangle duct, i see acme but dont like it,is ther any good prefab out there thats not slip and drive,just slips?
  10. Replies
    3
    Views
    886

    i guess i was thinking about a dual stage t-state...

    i guess i was thinking about a dual stage t-state a control guy was messing with on another job,maybe they had more units or a different problem? thanks for the reply
  11. Replies
    3
    Views
    886

    working on a resturant doing some relocation work...

    working on a resturant doing some relocation work and the owner asked a question that control wise i wasnt to sure about, he asked if he could put an additional heat/cool unit on the dinning side to...
  12. Replies
    1
    Views
    668

    looking for advice on where to drain condensate...

    looking for advice on where to drain condensate water from a 90+ furnace located on a second floor, i was going to gravity drain it along with the a/c condesate to the outside,but im worried about it...
  13. Replies
    3
    Views
    559

    thanks dash learning to do the design end is...

    thanks dash learning to do the design end is harder than the install ,thanks for the advice
  14. Replies
    3
    Views
    559

    using heat load calc or rule of thumb for...

    using heat load calc or rule of thumb for estimating,i was curios about what to do when i run into a house for example....2 floors,900sq ft 1st,750 sq ft 2nd a heat/cool unit in the basement and a...
Results 1 to 14 of 14
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event