Search:

Type: Posts; User: btuhack

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. If it's available, I'd like the status of: Pro...

    If it's available, I'd like the status of:
    Pro member/worldwide sex symbol for women to objectify.
  2. What exactly is a "HTalk Community Leader"?

    What exactly is a "HTalk Community Leader"?
  3. Rubber pads between the unit and bracket might...

    Rubber pads between the unit and bracket might help.
  4. Replies
    7
    Views
    462

    Obamacare

    Obamacare
  5. Replies
    13
    Views
    951

    I like to fiddle with some negotiators when...

    I like to fiddle with some negotiators when handing them a bill.

    "That'll be $xxx.xx not including gratuity..." nodding my head up and down and give them a dull look like I may not necessarily be...
  6. To work well, any attempt to match the equipment...

    To work well, any attempt to match the equipment capacity with zone demands is something you want. 2 zones will work better (for the equipment) than 3 zones will with 2 stage equipment. Done...
  7. Replies
    20
    Views
    1,178

    Mini's seem to be hypersensitive to clean coils,...

    Mini's seem to be hypersensitive to clean coils, clean wheels, and managing the condensate.

    I think the chemical use issue is with condensate and coil velocity. The condensate flows easily off a...
  8. Thread: Little help

    by btuhack
    Replies
    3
    Views
    246

    My "approved" method is by the book, same book...

    My "approved" method is by the book, same book that the inspector has read. Part of your method requires thought and reasoning on the inspectors part which is not something you want them doing....
  9. Develop a consistent pattern of treating him as a...

    Develop a consistent pattern of treating him as a fart target and he may. Smile as you do so and before long, a smile alone will chase him away.
  10. Thread: Little help

    by btuhack
    Replies
    3
    Views
    246

    I roll the VB and insulation back, then use mud...

    I roll the VB and insulation back, then use mud on the connectors, then zip tie the core over the mudded connector, then position the insulation, then overlap the VB and tape with venture tape. Never...
  11. Yup, ever see a scuff mark on a factory joint?...

    Yup, ever see a scuff mark on a factory joint? Nope. Not all, and maybe all, mfg's don't run a purge. I seriously doubt that they use a micron gauge during evacuation.

    If Doc is a doc, boy do I...
  12. You have a bunk board or some sort of mismatch of...

    You have a bunk board or some sort of mismatch of load/equipment capacity due to zoning and the wiring discrepancy is a work around. Either way, the wiring was deliberate and the reason needs to be...
  13. New equipment won't solve zoning design schemes...

    New equipment won't solve zoning design schemes such as a zone consisting of 18% of the total volume.

    You have fundamental problems and I'd put little faith in the folks that have visited you....
  14. Replies
    15
    Views
    2,183

    No, the inefficiency of bypass is still an...

    No, the inefficiency of bypass is still an approved strategy. There was talk about discontinuing energy credits for BP with regard to title 24 modeling/compliance/reports but retrofit apps were never...
  15. Replies
    15
    Views
    2,183

    FYI, code requires that a condensing furnace have...

    FYI, code requires that a condensing furnace have a drained overflow pan(drain terminated at a conspicuous location) not just the ac coil, when above a finished ceiling/surface.

    Sorry to hear...
  16. Replies
    14
    Views
    672

    I'll assume the thing the furnace is sitting on...

    I'll assume the thing the furnace is sitting on is just a base and not the sole return path. Could be a door seal or something to do with the omitted trap when the fan is on high.

    Then again, the...
  17. Replies
    9
    Views
    465

    Sloppy business/trade practices, inadequate...

    Sloppy business/trade practices, inadequate regulation, and shortsighted customers either don't know, are willing to pay for, or demand proper procedures. The bush league contractors figure if...
  18. Myth, fact, or somewhere in between. Myth- Big...

    Myth, fact, or somewhere in between.

    Myth- Big companies are always reputable and their cookie cutter methods are in the customer's best interest. Folks take decision shortcuts and mistake brand...
  19. Moonlighters or the scum of the earth. If they...

    Moonlighters or the scum of the earth. If they were any good, they'd be working for a good outfit keeping them too busy to consider unlawful business practices. Their customers get what they deserve....
  20. Replies
    5
    Views
    416

    With the job engineered, the answers you want...

    With the job engineered, the answers you want exist. How long it takes to discuss your concerns is where the problem develops.

    The contract defines the rules you're playing by...you get X and...
  21. Replies
    10
    Views
    523

    "She/they just spent (around) $600 plus for the...

    "She/they just spent (around) $600 plus for the E.A.C. I'm not so sure they want to start using box filters at $20 a pop. The electronic air cleaner are nice if they're maintained properly."

    so...
  22. Replies
    10
    Views
    523

    delete

    delete
  23. Thread: john stabile

    by btuhack
    Replies
    3
    Views
    366

    This thread is making me thirsty. I think I'll...

    This thread is making me thirsty. I think I'll have a beer.
  24. 92,000 btu's for 1400s/f in California? No way a...

    92,000 btu's for 1400s/f in California? No way a load calc was done. The furnace is probably 100% oversized for the house, and now you want to cobble together an A/C to go along with it for year...
  25. Replies
    15
    Views
    866

    See the attached. Bypassing air kills efficiency....

    See the attached. Bypassing air kills efficiency. You're much better off with oversized ducts and spilling the unwanted air to non calling zones.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event