Search:

Type: Posts; User: JoeVibe

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    2,584

    Hi Fixerup, Why was the bearing loose on the...

    Hi Fixerup,

    Why was the bearing loose on the shaft? Was a taper lock loose or was the shaft worn and if so was the fit repaired? Even if you made the shaft repair, this most likely wasn't the...
  2. Replies
    14
    Views
    2,584

    Captinsano and jdcoolj are right on all counts. I...

    Captinsano and jdcoolj are right on all counts. I just want to repeat that a good vibration analyst will be able to tell you if the source of the problem vibration is imbalance; misalignment;...
  3. Replies
    14
    Views
    2,584

    In my experience, when air handlers are shaking...

    In my experience, when air handlers are shaking it's almost always unbalance. It's actually rare that I walk up to a fan assembly that is properly balanced.
  4. Replies
    14
    Views
    2,584

    I'm NOT an HVAC guy (as those that know me can...

    I'm NOT an HVAC guy (as those that know me can tell you) but can't you check flow across the coils, or pressure drop, or something, to determine if they're blocked?

    I'm definitely biased but I...
  5. Replies
    18
    Views
    1,821

    Yes sir! In a couple more years I'll be changing...

    Yes sir! In a couple more years I'll be changing my screen name to JoeVegas.
  6. Replies
    18
    Views
    1,821

    TunaGuy - I sent you an email about your CSI...

    TunaGuy - I sent you an email about your CSI stuff.
    I demo'ed an older version Commtest box but I've not played with the VB7. It was a single channel box, maybe a 3000 or VB5, I can't remember. At...
  7. Replies
    18
    Views
    1,821

    Tunaguy is right on both counts. Commtest makes...

    Tunaguy is right on both counts. Commtest makes some good equipment, quite a few of the Trane offices use it. And it takes a lot of work to get good at vibe analysis. If you go at it half-hearted you...
  8. Replies
    18
    Views
    1,821

    Most large industrial sites and a lot of smaller...

    Most large industrial sites and a lot of smaller ones are doing vibration analysis, either in-house or through a contractor. Like you said, being able to predict failures and to make small repairs...
  9. Replies
    18
    Views
    1,821

    Hi Who, The data collector I use can be seen...

    Hi Who,

    The data collector I use can be seen at http://www2.emersonprocess.com/en-US/brands/csitechnologies/pva/csi2130/Pages/CSI2130MachineryHealthAnalyzer.aspx
    and the software at...
  10. Replies
    18
    Views
    1,821

    Hi Tx, I think the DFW class happened in...

    Hi Tx,

    I think the DFW class happened in 2007, just before I started teaching my classes but it was done by a good friend of mine from Mobius. I know all of the people at Mobius very well and, in...
  11. Replies
    18
    Views
    1,821

    Hi Teckster, My intent for this post was to...

    Hi Teckster,

    My intent for this post was to get to Trane techs that might not hear about my Trane classes. I try to notify as many offices as I can but sometimes it seems that the info doesn't...
  12. Replies
    18
    Views
    1,821

    Vibration Analysis training for Trane techs

    The fine folks that run this site have allowed me to post this notice.

    My name is Joe Gurney and I am a certified Level 4 vibration analyst and Level 3 vibration analysis Instructor working out...
  13. Replies
    4
    Views
    501

    Do you have the serial number? I'm not sure I can...

    Do you have the serial number? I'm not sure I can help but I'll try.
  14. Replies
    4
    Views
    855

    Jay, I sent you current contact info by...

    Jay,

    I sent you current contact info by email. Give me a call.

    Joe
  15. Replies
    19
    Views
    930

    The more I read this board the more impressed I...

    The more I read this board the more impressed I am with the depth of talent and information that's here. I'm still wading through the Pro forums. if I'm not careful I may end up understanding what...
  16. Replies
    19
    Views
    930

    Thanks for all of your responses. I didn't mean...

    Thanks for all of your responses. I didn't mean to try to rush things, I was just curious. This is a really good board and I'm looking forward to seeing what the Pro side has to offer.
  17. Replies
    19
    Views
    930

    Thanks.

    Thanks.
  18. Replies
    19
    Views
    930

    Pro Membership status

    I applied for pro membership about two weeks ago and I was wondering if someone could tell me how long it normally takes to hear something?

    Thanks - Joe
  19. Replies
    17
    Views
    1,198

    Sorry I didn't post earlier. I stay on the road a...

    Sorry I didn't post earlier. I stay on the road a lot and don't always have time to look at the message boards. I saw your first posts but I wasn't sure what you were asking.
  20. Replies
    17
    Views
    1,198

    Your motor guy is right. 3 phase AC motors don't...

    Your motor guy is right. 3 phase AC motors don't have armatures in them they have squirrel cage rotors. Armatures are found in DC motors and small AC motors like in power tools. There is no...
  21. Replies
    23
    Views
    2,485

    Thanks for all the great suggestions.

    Thanks for all the great suggestions.
  22. Replies
    23
    Views
    2,485

    Thanks. I'll add it to the list.

    Thanks. I'll add it to the list.
  23. Replies
    23
    Views
    2,485

    The person that I was asking for is located on...

    The person that I was asking for is located on the island Malta. I'm not sure what resources they have there. I think websites may be his best bet, but thanks for the suggestion.
  24. Replies
    23
    Views
    2,485

    Thanks for the recommendations!! I'll pass them...

    Thanks for the recommendations!! I'll pass them along.

    Joe
  25. Replies
    23
    Views
    2,485

    Thank you, sir. I will look into that. - Joe

    Thank you, sir. I will look into that. - Joe
Results 1 to 25 of 62
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event