Search:

Type: Posts; User: bobbykid

Search: Search took 0.01 seconds.

  1. Replies
    14
    Views
    894

    Not a DIY site?

    Been there? I know people in the past have thought you were too anal about people's inquiry's here in terms of fixing there ****. So my my motor and squirrel cage are a little out of adjustment and...
  2. Replies
    7
    Views
    424

    I think I'm on to something. I went to replace...

    I think I'm on to something. I went to replace squirrel cage with new, but it was more warped than older one. I did replace housing though. I did notice one little thing. The belly band for the motor...
  3. Replies
    7
    Views
    424

    I'm getting the cage and housing replaced under...

    I'm getting the cage and housing replaced under warranty. Subtle little vibration is making me crazy.
  4. Replies
    7
    Views
    424

    Well I have taken the blower wheel out several...

    Well I have taken the blower wheel out several times, centered, removed damper, replaced damper, removed little balancers on squirrel cage. When all is dead quiet is when I can hear it. I went into...
  5. Replies
    7
    Views
    424

    Air Handler Vibration On Wall

    Hello guys, I was hoping someone might have some ideas to stop the vibration coming from my 2 ton Trane air handler installed above my hot water heater. It's hanging on the wall with some bracket on...
  6. Thread: Screen Cover

    by bobbykid
    Replies
    7
    Views
    1,455

    Thanks again!

    Thanks again!
  7. Thread: Screen Cover

    by bobbykid
    Replies
    7
    Views
    1,455

    Thanks for the ideas guys. The mesh looks like a...

    Thanks for the ideas guys. The mesh looks like a good idea, only I need to cut it to size, to wrap around.
  8. Thread: Screen Cover

    by bobbykid
    Replies
    7
    Views
    1,455

    Screen Cover

    Hey guys I just cleaned out my condenser and found a ton of these little palm tree nuts that managed to slide into the hood of my XL14i. Is there a screen I can use to cover top part of condenser?...
  9. Replies
    4
    Views
    1,164

    Yup, found some piping rubbing against panels,...

    Yup, found some piping rubbing against panels, and flooring. So I insulated them and unit runs quieter.
  10. Replies
    4
    Views
    1,164

    Ok, been working this issue for a while,...

    Ok, been working this issue for a while, obviously. I tried putting a little insulation rubber tape under cover connections going to fan motor, this didn't stop vibration. When I hold or even press...
  11. Replies
    4
    Views
    1,164

    Trane XL14i vibrating

    We installed my Trane 2 ton system about 6 years ago. To level and try and eliminate vibration, I placed 4 or five rubber feet under condensing unit. A few months ago, Brighthouse (tv) people showed...
  12. Replies
    16
    Views
    9,360

    Can I put more HP in my condenser fan motor?

    I've got an old Ruud and the condenser fan motor is failing. It's an Emerson, 1/6 hp, .9 amp, 208-230 volt 1075 rpm, 3 uf cap. I've got an AO Smith, 1/4 hp, 1.8 amp, 208-230 volt 1075 rpm, 5 uf cap,...
  13. Replies
    19
    Views
    2,548

    Check your pitch. Is your drain working right?

    Check your pitch. Is your drain working right?
  14. Go Sox, Go Pat's!

    Go Sox, Go Pat's!
  15. Replies
    8
    Views
    1,929

    Try not to use any soap if the coils are not too...

    Try not to use any soap if the coils are not too dirty. And use as less soap as you can to remove the dirt because when you wash a coil, your removing a certain amount of millage with it...
  16. Timberland Pros. Steel toe. They sell them at...

    Timberland Pros. Steel toe. They sell them at Sears for about 80 bucks. And there light too!
  17. Replies
    3
    Views
    783

    Thanks for your help guys. I was just getting a...

    Thanks for your help guys. I was just getting a good idea about increasing by a half ton based on my heat load during the summer afternoons. I've done an effiency test by calculating my amps,...
  18. Replies
    3
    Views
    783

    Hi, my name is Bob, and I have been perusing...

    Hi, my name is Bob, and I have been perusing these boards rarely for the past couple of years. I was wondering about replacing my Heil air handler which is a 2 ton, and 17 years old, as well as my...
Results 1 to 18 of 18

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Comfortech 365