Search:

Type: Posts; User: zeppelin913

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    258

    Bacnet Stat w/dehumidification

    Does anyone know of a Bacnet programmable fan coil thermostat like the Honeywell TB series that will do dehumidification with a modulating reheat? It looks like the Viconics/Honeywell/JCI/etc brand...
  2. Replies
    1
    Views
    159

    Trane BCI-C RTAC Chiller Setup

    I'm trying to set up a RTAC chiller with a BCI-C bacnet controller. I've setup the baud rate and address on the controller. Following the integration instructions, using Techview I tried to enable...
  3. Replies
    0
    Views
    177

    Multiple Fan Coils, 1 Thermostat

    Has anyone tried connecting 2 modulating chilled water fan coil units to a single Honeywell TB7300 Series thermostat? Both units would run in tandem whenever there is demand.

    Thanks
  4. Replies
    1
    Views
    243

    Honeywell Spyder & 4-20ma Inputs

    Do the Honeywell Spyder controllers accept 4-20ma Inputs? Besides replacing the sensors with 0-10v sensors, is there any other work around for a 4-20ma sensor?
  5. Replies
    15
    Views
    1,932

    I know this is an old thread but I had the same...

    I know this is an old thread but I had the same questions and it help me find some answers. It looks like the connector is now available from Mitsubishi as part no. PAC-715AD. Here's a link to the...
  6. Replies
    6
    Views
    609

    Flow meter/switch

    Does anyone know of a flow meter that has both analog and binary outputs. I am trying to remove a flow switch that is being used for a chiller and replace it with something that can act as a switch...
  7. Replies
    0
    Views
    692

    Austin Controls Job

    Looks like the Texas Facilities Commission is hiring a controls guy if anyone is interested. Here is the link to their posting on the work in texas website.
    ...
  8. Replies
    4
    Views
    874

    I just reviewed the programs in CCT and found a...

    I just reviewed the programs in CCT and found a Zone Netsensor that was in the originally program but the inputs were hardwired instead. Deleted the "occupied mode" output point and it was removed...
  9. Replies
    4
    Views
    874

    Thanks for the replies...I looked at it today and...

    Thanks for the replies...I looked at it today and the light is actually flashing. I'm looking into your suggestions. Let me know if you have any other ideas.

    Thanks
  10. Replies
    4
    Views
    874

    JCI FEC Fault Light

    I have an Johnson Controls FEC 1610 that has a fault light on. The programming and boot versions were updated about 6 months ago. It is communicating and operating correctly. What does this fault...
  11. Replies
    4
    Views
    797

    Weather Station

    Does anyone have any recommendations for a high quality weather station to measure outside air temperature and humidity? I would like it to be compatible with either a Siemens or JCI controls system.
  12. Replies
    7
    Views
    728

    UPS with external contacts

    Does anyone know of a small UPS that has external contacts for battery level/alarms? I have some UPSs on my controllers that are in remote locations where no one hears the audible alarm and would...
  13. Replies
    8
    Views
    711

    The points are on a DCM and are PID loops. ...

    The points are on a DCM and are PID loops. Whenever they were programmed, they did not use a separate variable for the setpoints so to adjust them you must command the PID setpoint. I have tried...
  14. Replies
    8
    Views
    711

    This is on version 3.0. When I try to add the...

    This is on version 3.0. When I try to add the points to the NC, they don't show up in the list of points discovered but when I look at the engineering tab for the integration they are listed and...
  15. Replies
    8
    Views
    711

    PMI Point Migration

    I have a bunch of points that were migrated to JCI Metasys from PMI but I noticed some of the setpoints that are used for PID loops are not available in the points list in Metasys. Is there a way to...
  16. Replies
    6
    Views
    796

    Go to the system activity log. On the top menu,...

    Go to the system activity log. On the top menu, select query. You can select your options there. Limit it to certain points, users, and select the date range.
  17. Replies
    13
    Views
    1,154

    Sounds like this is the way to go for me. Thanks...

    Sounds like this is the way to go for me. Thanks for all the help and information.
  18. Replies
    6
    Views
    1,021

    So would the FX 60 be a direct replacement for...

    So would the FX 60 be a direct replacement for the NAEs? What about an NIE? There are still 2 buildings with old PMI controls. JCI hasn't really mentioned putting a FX60 as a replacement but it...
  19. Replies
    13
    Views
    1,154

    So instead of buying a PXC with bacnet...

    So instead of buying a PXC with bacnet capabilities I would have them buy the single site bacnet license for insight and set up a new bacnet bln. If I went with bacnet IP instead of MSTP then I...
  20. Replies
    6
    Views
    1,021

    Metasys Update

    I have a site that is running Metasys version 3.01 that is looking to complete an upgrade. They were told by JCI that some of the NAE's were not compatible with upgrading the system to 4.x or above....
  21. Replies
    13
    Views
    1,154

    It is for an Apogee system with a PXC Modular...

    It is for an Apogee system with a PXC Modular controller with P2 and BACnet. These tools are required to build the application and add it to system profile to view the points. The application has...
  22. Replies
    4
    Views
    684

    I think the fact you have exposure to controls...

    I think the fact you have exposure to controls and even have taken courses will definitely help you. I often see control companies hire people with no actual controls experience at all and some of...
  23. Replies
    13
    Views
    1,154

    Siemens Integration

    I'm working on a BACnet chiller integration into a Siemens control system and am needing the application builder and firmware loading tool to get my points in the BAS. Anyone out there have a copy...
  24. Replies
    16
    Views
    1,396

    Have you tried making a new program in CCT custom...

    Have you tried making a new program in CCT custom to your system?
  25. Replies
    16
    Views
    1,396

    What version of CCT do you have? Applications...

    What version of CCT do you have? Applications built in newer versions are not compatible with older versions.
Results 1 to 25 of 44
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event