Search:

Type: Posts; User: JPJ13

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    4,048

    Geothermal Purge/Flush Cart

    Hey all, I'm curious to know how much some of you paid for your purge carts, and where you purchased them from. My company is looking into buying one pretty quickly due to a new construction job we...
  2. Replies
    2
    Views
    1,491

    Im not as familiar with the York Affinity as I am...

    Im not as familiar with the York Affinity as I am with other models, but without any of the servie or installation literature for it my question to you is, what on this furnace can tell the board...
  3. Replies
    7
    Views
    749

    Freaking hilarious!! You have to do more of...

    Freaking hilarious!! You have to do more of those. Your comments on each step makes me laugh!
  4. I wouldn't pump it down in this case. If it does...

    I wouldn't pump it down in this case. If it does end up being partial restriction or non condensable, you may end up just moving it into condenser. I would suggest complete recovery, and weigh what...
  5. Replies
    7
    Views
    780

    A company I worked for from 2007-2011 used that...

    A company I worked for from 2007-2011 used that exact software for residential load calculations. I performed several of those calculations for that company with that software, so I can tell you...
  6. Replies
    8
    Views
    1,089

    To me it's a no-brainer.... a 20 yr old heat pump...

    To me it's a no-brainer.... a 20 yr old heat pump with a bad reversing valve? Time to replace the system. They would be crazy and stupid all rolled into one to put any major expense into a system of...
  7. Thread: Simple question

    by JPJ13
    Replies
    7
    Views
    565

    I would imagine your situation isnt much...

    I would imagine your situation isnt much different from when I use to repair household refrigerators that had 134A in them. When I changed a compressor in a fridge I made sure to replace the drier,...
  8. Replies
    8
    Views
    1,089

    Ok, in that case you have two problems.... 24v to...

    Ok, in that case you have two problems.... 24v to reversing valve in both modes, and stuck in cooling operation no matter what. Im very suspicious of the reversing valve, and either a problem with...
  9. Replies
    8
    Views
    1,089

    Well, if you are getting 50 psi on the liquid...

    Well, if you are getting 50 psi on the liquid line and the common suction port and a higher pressure of 120 psi on the vapor line, then you are definitely not in cooling mode. It is in fact in the...
  10. Replies
    14
    Views
    1,465

    excellent pics.... now if only they made clear...

    excellent pics.... now if only they made clear shells for the compressors...lol
  11. Replies
    13
    Views
    1,718

    Im in the Norfolk area, and the dual fuel...

    Im in the Norfolk area, and the dual fuel applications have become even more abundant over the past few years. I personally love them, as long as they are setup correctly. If they are setup using a...
  12. Replies
    9
    Views
    1,142

    In my neck of the woods the air handlers are in...

    In my neck of the woods the air handlers are in the attic about 70% of the time. Our code was changed in 2010 that all ductwork, regardless of location, has to be insulated to a value of R8.

    I...
  13. Replies
    21
    Views
    1,228

    Like most of you here, I prefer to inform the...

    Like most of you here, I prefer to inform the customer of all available options, which will include the pros and cons of each, and then let him decide which direction he wants to go.
  14. Replies
    10
    Views
    645

    Not the ideal location, but it would at least...

    Not the ideal location, but it would at least provide some safety protection from overheating, as long as the temperature isn't set too high. I wouldn't worry too much about any strain put on that...
  15. Replies
    13
    Views
    1,452

    The 16i does have the start kit, and is two-step...

    The 16i does have the start kit, and is two-step compressor.
  16. We all know the coil is before the heat strips on...

    We all know the coil is before the heat strips on a heat pump air handler to keep the refrigerant pressure from spiking. However, what do you think would be wrong with the blower first, then the...
  17. Replies
    6
    Views
    737

    Sounds like a possible return air issue. When you...

    Sounds like a possible return air issue. When you have the blower door off the furnace is getting sufficient return air through the opening and it runs smoothly and quietly...then once the door is...
  18. Replies
    9
    Views
    744

    I've done several of these, and you cannot charge...

    I've done several of these, and you cannot charge in heat with the charge assist. Only in AC mode with ODA above 70 degrees.
  19. Replies
    15
    Views
    1,593

    That's awesome. Hang on to that antique :yes:

    That's awesome. Hang on to that antique :yes:
  20. Replies
    13
    Views
    1,452

    There are heat pumps in Wisconsin?

    There are heat pumps in Wisconsin?
  21. Replies
    13
    Views
    1,452

    If caps are blowing out completely then I suspect...

    If caps are blowing out completely then I suspect it's an issue with the compressor. I'm afraid your best bet here is replacing it.
  22. Replies
    13
    Views
    1,452

    I would be extremely suspicious of compressor...

    I would be extremely suspicious of compressor issues. Of course, I would rule out the obvious factors, such as overcharged, restriction, voltage spikes, etc. Is the start cap actually burning up, or...
  23. Thread: Fan getting hot?

    by JPJ13
    Replies
    11
    Views
    645

    Most likely the insulation of the windings in the...

    Most likely the insulation of the windings in the motor are weakened enough to cause a 'grounded' condition. If you have a megohm meter you can check that more effectively. I think you are going to...
  24. Replies
    9
    Views
    545

    If it was only tripping from a dirty filter and...

    If it was only tripping from a dirty filter and hasn't been doing it for long, then I would leave the limit switch be, and only replace if it presents an issue later.
  25. Thread: CARRIER/BRYANT

    by JPJ13
    Replies
    14
    Views
    1,998

    The only issues I have with Carrier/Bryant is...

    The only issues I have with Carrier/Bryant is with their residential package units and commercial equipment. As fas as residential split systems, go I feel it is a good product and well worth...
Results 1 to 25 of 34
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event