Can I use this Router with Alerton Envision 2.6,Before I am using Contemprory Controls BAS Router.Thanks.
Type: Posts; User: coldrig
Can I use this Router with Alerton Envision 2.6,Before I am using Contemprory Controls BAS Router.Thanks.
Thanks all who try to help.
Which Software required to reprogram. Thanks.
Chiller Tripping on Control Power Loss,It is probably " ICVC Chiller HMI Display Model CEPL 130445-03
faulty. If we replace it with new one is it plug and play type or some programming required....
Problem solved found one contactor coil short. Thanks everybody.
Everything is bound. I check twice.
There are 4 compressor if problem with control Transformer then why fault is only with one particular compressor. There is only one control Transformer.
Chiller # 2 : Starter Fault Type 1 Cprs 2A. All contactors are checked and did not found any short what other possible cause for this problem, Thanks.
Starter Fail to Arm Start Comp 2A, How to fix this problem. Thanks.
Front Panel Chilled Water Setpt is 41 F and Active Chilled Water Setpt is 46. I don't know why Active Setpt is not lowering from 46. When I try from setpoint Screen If I raise 41 to 42 The Active...
Yes It is Adaptiview .
To change faulty Temprature Sensor, is it same procedure like changing LLID on RTAC Chiller with Dynaview or different. Thanks.
Thanks for your reply. I check 1 is +5V and 4 is Ground. Please you also check it. Anyhow it is Straght Cable and ready made available no need to make myself. Thanks again.
Anybody have idea of Trane Techview Serial Cable Pinout. I had before one which I lost I want to make new one. Thanks.
Is there any substitute To Trane Chiller RTAD EXV Module MOD0188E. Thanks.
Following Error is showing on Display screen "" Application has failed to start because winsrv was not found.Reinstalling application may fix this problem"" I try to check with Key and found Up and...
UDP Port not accepting more than 4 Digits. I am attaching configuration picture.
I have Portable BASRT Router it was working fine,Now it is not detected with Alerton Envision 2.6 when I run Device Manager, But when I open its Web Page 192.168.92.68 it is opening what is possible...
What is name of Book and where to get that. Thanks.
Which Software is used to check YORK CENTRIFUGAL CHILLER YK for troubleshooting. Where get this software. Thanks.
Hi Apprentice3
Thanks for your detailed reply I will try and let you know the result.
I download and install pCOManager I am sending Picture what I have 3 Items and Controller do you any idea if I can read program from controller. pCOManager program showing Serial o is for pLan but...
Anybody have idea which software is used to access McQuay Chiller Controller pCO3. What is use if itool software. Thanks.
Reckles Thank you very much.
If I want to add one new VLC in Envision 2.6 Network what is right sequence. Thanks.
Now concept is clear. Thanks.
Thanks very good Document. Can you tell me What means BR in Function output.
AI,BI,AV,BV,AO AND BO are understandable BR stand for what. Thanks.
Thanks both of you.For sharing solution.
Can I use PI Function only as Proportional mode.Thanks.
Yes we have 2 more chillers like that.
Yes there is Tx and Rx on Starter Board.I am attaching Pictures there is Activity on Microboard Tx Rx but no light at all on SSS Board Tx Rx.
I check and found Logic board is not talking. Microboard Tx and Rx flashing but no flashing on starter board.No light at all.
I check and found Logic board is not talking. Microboard Tx and Rx flashing but no flashing on starter board.
I will check and let you know. Please see new pictures Y1 picture is broken wire. Thanks.
Please check new pictures.
I upload 4 Files for boards and their numbers. 1 File which has circle and arrow is broken wire can it be reason. Thanks.
We have York Centrifugal Chillers YK Series It is showing Starter Module Invalid and " X " with Voltage
Current and Temperature for Phase A , B and C. What is possible cause. Thanks.
I am just trying to bind,It is our new contract I found this alarm and when check the binding found these two items Red face and when try to bind it is not binding.There is one Card UCP3 DUAL BINARY...
Yes I have that tool. Thanks.
Carrier 1 Thanks It is not LonTalk,I am using TechView.
Anybody has idea how to bind following two
1: Status Relays.e.g Alarm,Limit Mode,Running
2: External Auto/Stop and Emergency Stop
Thanks for any help.
Please see Fig what is possible problem with this Chiller. Thanks.
For Chiller RTAC inlet and outlet Sensors are SEN02133. Is it possible if we can use SEN1960 which has same 10K resistance as SEN02133. Can we reprogram SEN1960 to work as Low Temperature.
Thanks,Chillersvcman.
RTAC200 oil separator very high whistling sound any body knows the reason.Thanks.
Thanks for Advice.I will do that.
Thanks Heavyevans The Screen you refer is for RTAC Chillers it is for Dynaview not for RTAA Clear Display.
Any body has idea if RTAA Clear Display Membrane Keypad is available. Thanks.
RTAC200 oil separator very high whistling sound any body knows the reason.Thanks.