Search:

Type: Posts; User: #1servicetech

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    85

    Carrier 6400 controller problem

    I have a xl23 chiller with a carrier 6400 controller. I uploaded the program and was going to make a few changes. when I tried to click on controller to look at the setup, it was greyed out and...
  2. Thread: Lon Plug

    by #1servicetech
    Replies
    11
    Views
    384

    I think I found it on Mouser. I will post the...

    I think I found it on Mouser. I will post the part number if it is right. I went to the site you book marked and there is a 27.00 surcharge to cover the minimum.
  3. Thread: Lon Plug

    by #1servicetech
    Replies
    11
    Views
    384

    Thanks for the numbers. both sites don't show...

    Thanks for the numbers. both sites don't show anything online so I will give them a call tomorrow.
  4. Replies
    4
    Views
    233

    I would just use a MUX to put the setpoint or...

    I would just use a MUX to put the setpoint or input to a value that would make the pid go to 0
  5. Thread: Lon Plug

    by #1servicetech
    Replies
    11
    Views
    384

    I went to both sites and put in the numbers that...

    I went to both sites and put in the numbers that are on the plug but there are so many. does anyone have a part number?
  6. Thread: Lon Plug

    by #1servicetech
    Replies
    11
    Views
    384

    Lon Plug

    I have the lon usb adapter. The plug is getting a little worn and I sometimes have to adjust it to get communication. does anyone know where I can get a new plug for this? I am talking about the...
  7. Replies
    13
    Views
    1,521

    without the original disk you probably won't be...

    without the original disk you probably won't be able to reinstall it. did you have graphics? if you did you may be able to save those.
  8. I just read a previous response and you said you...

    I just read a previous response and you said you have the old hard drive in the new computer. did you release the authorization code from the old computer and reregister it?
  9. Is there an address written anywhere on the bcu?...

    Is there an address written anywhere on the bcu? if this is bacnet IP the workstation will need to be in the same subnet address range to connect.
  10. Are you using a crossover cable? you need a...

    Are you using a crossover cable? you need a crossover cable for the computer to bcu connection.
  11. Replies
    5
    Views
    290

    Thank you. I will give this a try.

    Thank you. I will give this a try.
  12. Replies
    5
    Views
    290

    Trane BCI-R problem

    Good morning all.
    I have a trane BCI-R that is giving me problems. I have a jace installed with the mstp license and I can see all of the points fine. I turned on BO1 which is supposed to enable...
  13. Replies
    7
    Views
    321

    The PC

    The PC
  14. Replies
    7
    Views
    321

    I just rechecked and you are right on both counts.

    I just rechecked and you are right on both counts.
  15. Replies
    7
    Views
    321

    I thought that might be the case. I have switched...

    I thought that might be the case. I have switched it all to a laptop with a modem for now and will upgrade it all as soon as possible.
  16. Replies
    7
    Views
    321

    old alerton TUX

    I have an old alerton tux system. it has an ISA card in the old computer which has died. it says IBM Lan card and has only 2 wires to a 25 pin rs232 type connector. is this an RS485 card? can I use a...
  17. yes, you would need to set up a VPN or use log me...

    yes, you would need to set up a VPN or use log me in.
  18. yes, it will work fine on a 64 bit computer. I am...

    yes, it will work fine on a 64 bit computer. I am running version 17 on a 64 bit win7 computer currently and it all runs fine. as was said before, you need the latest service packs.
  19. Replies
    1
    Views
    220

    Staefa Jace

    Does anyone have the staefa jace default platform password?
  20. Replies
    1
    Views
    328

    How are you starting them up? are you using the...

    How are you starting them up? are you using the run*.bat for them?
  21. Replies
    9
    Views
    1,254

    Could I get a copy of that also please?

    Could I get a copy of that also please?
  22. Replies
    3
    Views
    312

    If I remember correctly it would give you the...

    If I remember correctly it would give you the name and ask if you still want to log in using that name. have you gone into the setup and put the correct port number and baud rate? at the first screen...
  23. Replies
    3
    Views
    312

    Are you using PCLedit or PCMedit? what kind of...

    Are you using PCLedit or PCMedit? what kind of computer comm port are you using?
  24. Replies
    4
    Views
    395

    The baud rate could actually be anything. it is...

    The baud rate could actually be anything. it is changeable. I would try 1200 first then try the others.
  25. Replies
    4
    Views
    395

    Are you using the Trane cable? did you try M with...

    Are you using the Trane cable? did you try M with your caps lock on?
Results 1 to 25 of 434
Page 1 of 18 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event