Search:

Type: Posts; User: thor7000

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    27
    Views
    1,228

    Thanks for the link......the oil does show signs...

    Thanks for the link......the oil does show signs of being burnt and also had metallic sludge on the oil pan.
  2. Replies
    27
    Views
    1,228

    definitely in the wrist pin....I checked the...

    definitely in the wrist pin....I checked the connecting rods on the crank when I replaced the oil pan gasket and everything looked OK. Just wondering if it's worth repairing or just scrap the...
  3. Replies
    27
    Views
    1,228

    The travel is more then an inch......when I...

    The travel is more then an inch......when I removed the head and valve plate I manually rotated the crank by pushing on the pistons, I noticed the slop then and used my magnetic pen to confirm. One...
  4. Replies
    27
    Views
    1,228

    so would the concensus be that the compressor is...

    so would the concensus be that the compressor is bad??? I'm feeling a little stupid with this freezer.....just thought I would help a friend out and now it's turned into a pain in the ass!!
  5. Replies
    27
    Views
    1,228

    the plate said operating pressures...... I...

    the plate said operating pressures...... I thought something was wrong with that too!!
  6. Replies
    27
    Views
    1,228

    I couldn't get any temperature in the...

    I couldn't get any temperature in the cabinet....the evap. coil wasn't even cooling down.
  7. Replies
    27
    Views
    1,228

    I don't think it was a conversion since the...

    I don't think it was a conversion since the freezer name plate shows R404a
  8. Replies
    27
    Views
    1,228

    [QUOTE=Boreas1;17565341]50 psig on 404a freezer...

    [QUOTE=Boreas1;17565341]50 psig on 404a freezer isn't a low suction it's high

    Sorry about my ignorance but it's been a long time since I worked on freezers......back in the R502/R12 days!!...
  9. Replies
    27
    Views
    1,228

    no receiver...it's a small unit, refrigerant is...

    no receiver...it's a small unit, refrigerant is 404a and no I can't check pressures on either side...just the outlet side on the compressor service valve. I tried driving it open and then closed to...
  10. Replies
    27
    Views
    1,228

    Need help with 2 door commercial freezer

    I don't usually get involved with this stuff but a friend asked if I could take a look. Here is the situation, it has a K body semi hermetic compressor that was leaking oil from the pan and the oil...
  11. Replies
    7
    Views
    1,495

    Solar refrigerant panels...???

    Sorry, I realize it's not Geo Thermal related but I was speaking to an individual yesterday and he was telling me about a new air conditioning system that they are selling which incorporates the use...
  12. Anyone in Central Florida looking for experienced Tech/Manager??

    Just recently moved down to Florida (Bradenton area) and am looking for work as a "sub contractor" to help out on existing or up coming projects. Majority of my experience is in the...
  13. Replies
    6
    Views
    774

    will get some pressure readings later today and...

    will get some pressure readings later today and post.
  14. Replies
    6
    Views
    774

    Need help with a res. Bryant heat pump

    I'm currently down at my house in Florida and have very little exposure to heat pumps especially being from Canada...plus I mainly work commercial/industrial equipment. A friend of ours has a Bryant...
  15. Replies
    2
    Views
    962

    would you consider a Canadian for your position??...

    would you consider a Canadian for your position?? I have residence in Bradenton??
  16. Replies
    16
    Views
    1,986

    anything related to the medical industry makes...

    anything related to the medical industry makes things allot easier to get a greencard!!
  17. Replies
    16
    Views
    1,986

    H1-B visas are really hard to get, basically you...

    H1-B visas are really hard to get, basically you have to prove to U.S. Customs that nobody within the U.S has the same qualifications as you.....if you find a company to sponsor you, you will need to...
  18. Replies
    12
    Views
    1,672

    sorry to burst your bubble but you don't have a...

    sorry to burst your bubble but you don't have a hope in hell to move and work in the U.S as an apprentice or even as a fully licensed journeyman unless you find a company willing to sponsor you...or...
  19. Replies
    11
    Views
    1,794

    Well said....seems like everyone is looking for...

    Well said....seems like everyone is looking for the "easy" way to get licenses/experience now a days...gets very frustrating!!
  20. Replies
    11
    Views
    1,794

    By going to school...:cheers:

    By going to school...:cheers:
  21. Sounds more like it's in the Quebec/ Montreal...

    Sounds more like it's in the Quebec/ Montreal area..?? Never heard of it before so just guessing!!
  22. Replies
    28
    Views
    2,252

    I have also been playing with the idea of moving...

    I have also been playing with the idea of moving down to the Tampa/ St. Pete's area from Canada. A few quick questions, are Canadian journeymen licences recognized in the U.S?? I have been thinking...
  23. Replies
    2
    Views
    1,368

    Been in the union quite a while ago, but from...

    Been in the union quite a while ago, but from what I remember you have to become a member first before applying for a union position...unless the position you are applying for cannot be filled by any...
  24. Replies
    16
    Views
    1,359

    You can't believe what the trade schools will...

    You can't believe what the trade schools will tell you!! Just a piece of advice....go for the job that will sign you up for an apprenticeship and don't worry too much about the pay right now (within...
  25. Replies
    16
    Views
    1,359

    Sorry to sound harsh, but your right out of trade...

    Sorry to sound harsh, but your right out of trade school with zero field experience...what did you expect as a wage?? $13-14/hr is right on...that's what we offer for guys just like you. Until you...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event