Search:

Type: Posts; User: tompass

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    41
    Views
    3,419

    Advanced Response, Only a HO but sounds like...

    Advanced Response,

    Only a HO but sounds like pulling a pin and running on first stage is way to go. Will give it further thought and do some research. Thanks so much.
  2. Replies
    41
    Views
    3,419

    Kind of dark in here right now but perhaps the...

    Kind of dark in here right now but perhaps the light will come on. Thanks for all responses and willing assistance.
  3. Replies
    41
    Views
    3,419

    According to printout from manual, I am only able...

    According to printout from manual, I am only able to get to 915cfm with single stage. Oh....perhaps D for cool tap and D for adjust tap?
  4. Replies
    41
    Views
    3,419

    With pins set on cool tap on D and adjust tap on...

    With pins set on cool tap on D and adjust tap on C provides 915cfm on high and 495 on low. Since it is single stage, I assume the low setting of 495cfm is not available.
  5. Replies
    41
    Views
    3,419

    Single stage AC. If I had a two stage, I could...

    Single stage AC. If I had a two stage, I could get CFM down to around 400 very easily. When this unit goes, I will replace with two stage. Must I replace with a York unit or do I have options?
  6. Replies
    41
    Views
    3,419

    PIXUC16V07501

    PIXUC16V07501
  7. Replies
    41
    Views
    3,419

    York Diamond 95 Ultra with VS 2 stage gas heater...

    York Diamond 95 Ultra with VS 2 stage gas heater circa 2002.
  8. Replies
    41
    Views
    3,419

    It is VS blower but again 915 is lowest setting...

    It is VS blower but again 915 is lowest setting using pins inside unit. This is a single stage AC unit although the heat is two stage.
  9. Replies
    41
    Views
    3,419

    Do not have the expertise to check pressures,...

    Do not have the expertise to check pressures, load, etc. so will likely be safe setting it the 900 cfm. Or at least, I hope so. Also just double checked and lowest setting is 900 cfm so will have...
  10. Replies
    41
    Views
    3,419

    Right. But not sure if the CFM was set to coil...

    Right. But not sure if the CFM was set to coil or condenser. At an rate, now set to 900 CFM so will keep an eye on humidity control.
  11. Replies
    41
    Views
    3,419

    I appreciate the response. Just a few minutes...

    I appreciate the response. Just a few minutes ago decided to set the VS blower to 900 CFM and watch RH movement.
  12. Replies
    41
    Views
    3,419

    Residential CFM/AC

    Outside unit is 2 Ton but coil is 2 5 Ton. What would the recommended CFM be for maximum humidity control? Presently set at 1000 cfm.
  13. Replies
    0
    Views
    343

    Bryant FV4 VS Filter

    The Bryant uses a hogs hair filter in a size that is not compatible with any commercially available 1" filter. Other than having a custom frame made and then periodically purchasing the inserts, is...
  14. Thread: Kool Cap

    by tompass
    Replies
    12
    Views
    2,112

    Well Gunny, that about sums it up.

    Well Gunny, that about sums it up.
  15. Thread: Kool Cap

    by tompass
    Replies
    12
    Views
    2,112

    Thought so. Thanks.

    Thought so. Thanks.
  16. Thread: Kool Cap

    by tompass
    Replies
    12
    Views
    2,112

    Kool Cap

    Does anyone have any info on this item. It sits on top of heat pump and "blows" upward when fan is running and then lays down on top of unit supposedly to protect motor from getting constantly...
  17. My experience that there are many good...

    My experience that there are many good professional HVAC guys and techs out there but there are also some lazy ones. The young man that they sent out to correct some problems with my new install had...
  18. It is likely in the manual. Have to enter...

    It is likely in the manual. Have to enter program mode and follow directions.
  19. Replies
    7
    Views
    546

    I ordered some pleated material from air sponge. ...

    I ordered some pleated material from air sponge. Will have to cut and fit to frame.
  20. Replies
    7
    Views
    546

    Isn't hammock spun fiberglass same as inexpensive...

    Isn't hammock spun fiberglass same as inexpensive bue $1 filters? Is present hogshair filter better than cheap disposable filters?
  21. Replies
    7
    Views
    546

    So what would the recommended material to be used...

    So what would the recommended material to be used in this frame? Pleated media?
  22. Replies
    7
    Views
    546

    Hammock Filter Material

    Recently purchased a custom made aluminum frame filter with screen and hinged sides. Am I correct in assuming that the direction of air flow should be first through the filter material and then...
  23. Replies
    2
    Views
    1,050

    Consider the 265ANA and FV4 variable speed...

    Consider the 265ANA and FV4 variable speed handler with preferred humidistat with outdoor sensor.
  24. Replies
    13
    Views
    5,820

    Interesting that the washable filters are...

    Interesting that the washable filters are standard on Bryant VS air handlers.
  25. That info is availavble on their web site. Just...

    That info is availavble on their web site. Just go to menu on left side of page where it says controls. Then select the Preferred stat. That page will have option for documentation and those...
  26. Replies
    1
    Views
    545

    Read the manuals for both the thermidistat and VS...

    Read the manuals for both the thermidistat and VS blower thoroughly and noted that the two jumpers, J1/J2, have to be removed on fan coil board and one of the dry contact terminals also must be wired...
  27. Replies
    1
    Views
    545

    Bryant T6-PRH Programming

    I have recently installed T6-PRH control with single stage HP and FV4B vs handler. I have no problem programming the thermidistat for functions 1-33 but it seems that functions 40-44 are not...
  28. Replies
    6
    Views
    906

    Something to consider. May just be enough room...

    Something to consider. May just be enough room to do that. This is a vertical installation so filter is at bottom and water heater just below. I will check that out.
  29. Replies
    6
    Views
    906

    I would love to use 4 or 5 inch box filter but...

    I would love to use 4 or 5 inch box filter but that would require some sheet metal work and not sure I have enough room between bottom of air handler and top of water heater to make that happen. ...
  30. Replies
    6
    Views
    906

    That is the problem. Not quite large enough to...

    That is the problem. Not quite large enough to stay in place so has a tendency to buckle as air handler ramps up.
  31. Replies
    6
    Views
    906

    Filter for Bryant FV4B Handler

    Seems that stock filter is a washable filter in metal frame that measures somewhat larger than standard paper 16X20X1 paper filter. Is it possible to use replaceable paper filter or must I somehow...
  32. Replies
    18
    Views
    1,205

    Thanks. Not encouraging news but I have...

    Thanks. Not encouraging news but I have familiarized myself with protocol required to enter program mode to properly configure the thermidistat. As far as dip switches and jumpers, that goes back...
  33. Replies
    18
    Views
    1,205

    Dash, I am using Bryant Preferred ...

    Dash,

    I am using Bryant Preferred Programmable Thermidistat so would same hold true?
  34. Replies
    18
    Views
    1,205

    Given that the purpose of the thermidistat is to...

    Given that the purpose of the thermidistat is to drop CFM when responding to demand for lower RH, your advice make good sense.
  35. Replies
    18
    Views
    1,205

    You may be right or may have meant that the CFM...

    You may be right or may have meant that the CFM for given tonnage is predetermined and then jumpers are set accordingly. Again, I am not on site and can not verify but will check it when I get down...
  36. Replies
    18
    Views
    1,205

    PS I actually stated 350cfm per ton is where I...

    PS
    I actually stated 350cfm per ton is where I wanted it set.
  37. Replies
    18
    Views
    1,205

    Being that this is a brand new install and I...

    Being that this is a brand new install and I explicitly instructed installer to set the FV4B at 2 tons to match the Preferred 15 seer 2 ton outside unit, I would certainly hope that that he...
  38. Replies
    18
    Views
    1,205

    Little River, SC is where unit is located. I am...

    Little River, SC is where unit is located. I am at a disadvantage presently because I am up in NJ.
  39. Replies
    18
    Views
    1,205

    Thanks. If the installer selected for some...

    Thanks. If the installer selected for some reason 400 CFM per ton when there is call for AC and I want 350 CFM, that adjustment should be able to be made. I am not saying it is set up incorrectly ...
  40. Replies
    18
    Views
    1,205

    Bryant FV4B/CFM

    Just had FV4B variable speed fan coil installed controlled by T6-PRH thermidistat. Outside unit is 265ana 15 seer HP. Both units are 2 ton units. Installer indicates that CFM can not be manually...
  41. I went with HW bypass fan driven humidifier and...

    I went with HW bypass fan driven humidifier and have been pleased with results.
  42. Replies
    17
    Views
    1,115

    Good deal, thanks.

    Good deal, thanks.
  43. Replies
    17
    Views
    1,115

    I am lost now. Consensus is that Bryant...

    I am lost now. Consensus is that Bryant Preferred Thermidistat will fully communicate with FV4 and Preferred 15 seer single stage electric HP using 8 wires?
  44. Replies
    17
    Views
    1,115

    So then the Bryant Preferred Thermidistat will...

    So then the Bryant Preferred Thermidistat will not allow me to control humidity by communicating with FV4 to ramp up or down in response to humidity set point? If that is the case, I should either...
  45. Replies
    17
    Views
    1,115

    That is good news. Thanks for double checking...

    That is good news. Thanks for double checking requirements.
  46. Replies
    17
    Views
    1,115

    So perhaps 8 wires would be sufficient to take...

    So perhaps 8 wires would be sufficient to take advantage of humidity control and allowing VS handler to ramp up and down?
  47. Replies
    17
    Views
    1,115

    I was led to believe that an outside temperature...

    I was led to believe that an outside temperature sensor was required to have the thermidistat operate properly. I also would think that outside temp would have little to do with RH reading inside. ...
  48. Replies
    17
    Views
    1,115

    Thanks. So essentially it is a waste of money to...

    Thanks. So essentially it is a waste of money to purchase the Bryant Preferred Thermidistat. Bummer for sure.
  49. Replies
    17
    Views
    1,115

    Should add that this will be used with Fv4 vs...

    Should add that this will be used with Fv4 vs handler and Preferred 15 seer single stage HP.
  50. Replies
    17
    Views
    1,115

    Bryant Preferred Thermidistat

    How many wires are required to allow the thermidistat to operate as intended by manufacturer. I assume that an outside temperature sensor is also requiredI presently have 8 available wires but not...
Results 1 to 50 of 147
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event