Search:

Any one connected Andover to a Jace without the head end? What is required for driver or are they bacnet... I am told we are looking at circa 1995 1996 VAV boxes...I hope to have a model number next...

Sorry to rub you the wrong way. I did not write it, but it does exist. I also would tell you more, but until I am given proper permission to do so I must stick by my word. I am sure it will...

Thanks, I am going to try to pull one in to a soft jace sometime just to see how they work. These boxes were running stand alone.

I had to remove some Reliable VAV controllers, will not go into reasons, but they are Bacnet...Right?
Can I pull them into a Jace or SoftJace? Do i need special software to set address or do they...

You have to live in Ohio. I am not at liberty to give out the information at this time. Just know that it is real. Sorry I cannot give you more.

YES!

ANy one use teletrol and AX, I have heard there is a driver floating around, but I wonder how good it is, and how big of a site? What kind of Performance? I have heard of one driver but it is so...

Just in case anyone has this issue with a Older Williamson Gas Furnace, I took the combustion motor off, and cleaned the flue, and the undersized condensate drains, there was a good amount of water...

I am working on an older Williamson 90 plus Nat.Gas furnace and it is rolling out at first light off. I have checked the pressures in the past and it looks good. I few years ago I installed a...

Well I got it to work, all but one point, The nviON/OFF will not come through. The factory said the csv file was correct and it should but they could not help so I had to hard wire the remote start...

Need to know if any one has used the Airstack chiller with the provided fieldserver to Lonworks. I would like to know if it went well and if you had any issues? I am using a Jace BTW. I pulled in...

Dell works best with Trane Software. Without all the extra junk on it.

I am being asked if there is a Honeywell XL 5000 integration method, I do not know anything about the Honey well line, so hoping to find some info.
All I know is that it is a HoneyWell XL5000....

Heat pump DIP SW settings, Off, ON, Off, dip 4 not used
Heat Pump with Econ, Off, On, ON, dip 4 not used

2 Heat 2 Cool, Off, Off, Off
2 Heat 2 Cool w Econ, Off, Off , ON

4 Cool On, Off, Off...

I did put that in my post, I agree 100% I was looking at it from the stand point of new commissioining, I think that is what I took from the original post that this is why he wanted the software was...

I know in my area the commercial office will sell the service Rover, this is a scaled down rover that will allow you to configure controllers. I guess it depends on the area you are in, Our local...

MAN there sure are a lot of TH,ers,LOL. That is Trane Haters by the way.

Let me put another spin on this.
If you are putting in the system wether it is Trane or Johnson or What ever, and you...

Depending on How old this chiller is, your best bet is to do Bacnet to a Jace, I do not think the UCP 2 on a CV can do LON. you get more information out of bacnet any way. You will need a BCU and...

DId you set the DIP switches correct on the TCI board? If this is an OLD varitrack it may be that the comm card needs to set up as nonisolated comm 3 comm 4, you do this by rotating the top portion...

You can take the model and serial number and order the options module as a replacement repair part. Just another option.

For the money just use the GBAS module and a Lon IO card of your choice and monitor the water temps with external sensors, program the GBAS to control set point and use the alarm relay to show...

I think you will see in the next year a change in the Open side of things, I have heard that they will be moving towards offering products that will be either bacnet or Lon at the device level. IMHO...

I know some one who has done this, but not sure if they want me to reveal who they are, only comm 4 though. Comm 3 was not worth the time they said.

The Kit is Easy! Just turn off power, remove duct, remove screws holding in the old valve, cut wires to motor as close as you can to the old motor and save, just in case you need the extra, put on...

Any one set up a Catapillar Generator Modbus serial on a Jace using AX? I am having some issues. I think it is more of the setup in the jace, and maybe a slight wire problem a close second. I...