the access panal was too low to get to damper so i had to take off drive cleat and open elbows side to access to damper to get heat until we replace it
Type: Posts; User: slowandsteady
the access panal was too low to get to damper so i had to take off drive cleat and open elbows side to access to damper to get heat until we replace it
thanks dandyme and pairman, i appriciate it, i am waiting to find out if they will do it now which is the best time before this problem kills the ign contr board and gas valve , i do have that...
flue heats up gas line to not only pre warm gas , but to evaporate condensate, this hurts to look at, thinking someone could leave it like that is down right scary
i found this comb blower running all the time 1.3 amps @230v, tech support said we need to change motor(which i figured) but said a conversion kit needs to be installed as well, from the literature...
replaced bad blower which someone else found dead. high limit was tripping out , went through system and this is what i found, guess we know what killed blower.
i think so, but wanted to know other peoples
ok carrier 10 ton rtu, fed area which is occupied by two spaces, dont know when they were seperated but were as one at one point. fed both stores but...
i havent heard of them, but, i think the only thing that would make it a pos would be the person installing it. just my opinion
strait a/c boss wants them started and checked to get paid, i dont add due to i dont want to over charge id rather wait til spring but not my call
:couchhide:
hello new installs and needed to start up, am i too picky or does it not make sense to start up and check correct pressures, or will you be able to get target sc in any temp
opinions anyone
the units have been serviced each year, im new here i was aked to do check ups and cleanouts when neccessary. i noticed some oil under burner, found oil in blast tube to under blower wheel , nozzle...
I have my oil license , but rent where im at and he wants me to take care of boiler, i noticed some dripage under burner and found pump at 100psi when running, when shuts off slow burn on flame...
I AGREE FRUECRUE THATS WHY I SAID AFTER BREAKER AND DISCONNECT FIXED WE WILL BE BACK. BEEN A WEEK AND NO PROBLEMS IT MUST HAVE BEEN BREAKER LIKE I SAID , BUT BOSS IS CONCERNED WHY IN 3 YRS...
:couch: SAM ADAMS ? MY FAVORITE CAN I SIGN UP. JUST TOLD BONUS WAS WE HAVE WORK (4DAY WEEKS ) FOR THE NEXT 2 WEEKS. WHICH I AM GREATFUL FOR .
:eek2: wow im sure they look forward to that each year :eek2:
when it fails DO NOT TOUCH IT then call someone and let them see it while in the failed state , not after its reset
no heat call old trane rtu non heat pump with electric heat, disconnect of ,found jumped out, only service switch is cb on first floor. i reset ran to roof, found all 3 banks working and at...
ok read page 48 it says it turns on 2nd stage if 1st stage can not handle capacity, seems to be working fine
well when whiskey isnt enough its time to bring in the THE GLUG when made right , and drank at right temp, bottle empties quick, well cheers \_/
having a few tonight for sure :couch:
no christamas party here ever, bottle of choice last year, doesnt look like its happeng this year, looks like only bounus this year is still having a job
well this is what my boss tells me to do when switching from r-22 to 410 make sure lines are not soldered, if so braze them. we do not carry nitro i know issues with c02 but its not my company, i...
ok i have been working on and installing some of these 90+ furnaces, first time i ever had to install a nuetralizer which will tie into drain in bathroom. what am i missing how often should this be...
I dont like going into home when empmty but oh well, its better than having there little dog jump on my leg annoying the the hell out of me where i feel like kicking the bas@#!* and saying shut the...
FINALLY slayer and megadeth together again, cant wait till feb to see them again.
damn slow here no work again, :couch: economist say its getting better :eek2: i dont see it
well i have to agree with whec720, there is too many but heres 2 of my favorites
http://www.youtube.com/watch?v=jgqxQmAbTBc
http://www.youtube.com/watch?v=b2za92DQOCw
Also, the outdoor temp sensor is installed in the air pipe right next to the furnace, they assured me that that is the correct place on a system like mine. Forced air, 20 year old Luxaire, 2000 sq....
i want to know 2 things
1) will he go for it again on 4th if in same situiation
2) am i the only one not missing matt light , vollmor not only has done well but has done great against...
well today i went back to change a stat which was defective, under warrenty, i was leaving and she handed me 10 bucks and says, thank you for comimg out, its nice getting the same guy, i said...
hello was at a checkup for heat today, start hum, check zones (3) , heater was ok all zones worked, what i did find was the barometric damper was not opening when 1 zone was calling. seemed to...
i didnt agree with changing only condenser, bosses decision, everything i did my boss told me to do, i said it may be problematic. he said after two filter changes it was fine, he didnt want...
we changed a condenser during the summer, evap on first floor , condenser on roof of 5 story building, before changing condenser( which boss condemned) he wanted me to isolate piping from evap to...
i beleive mine is ricthie had it for awhile it does swage and flare from 1/4 to 3/4 i think its best option then no guessing if you have the right size its no hammering has tool to...
i dont know havent figured it out yet
ok thanks
:oops: ok my bad i have small issues with temp range on glide, guess i should have used 400 for net not 350 i went back to my books and found two things, 1) need to pump analyzer 18 times ...
its a carrier puron, dont know if that helps
I am piping in a split system, not sure of size yet dont have equipment, i was told to run 3/8 and 1 1/8 from first floor to roof, from coil on furnace run length is approximately 45' going...
:couch: well since its thursday and i have fridays off, guess i should relax, and thanks guys for replys,
hi new to site i just wasnt sure how slow people are, we do 95% resi and we keep getting laid off we barely have work when were not laid off we work four day work week and less than 6 employers...
HELLO i just changed oil filter, strainer,electrodes,and nozzle to a hot air furnace. old eff ticked said 400 total stack 350 net and running 84% room @50f
i found stack at 500, net was 375 with...