Search:

Type: Posts; User: johnbeck1000

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    395

    Need advice

    Hey guys I'm in the trade but I need some help. My dad and step mom live in Monrovia, CA and their AC died and now need a new one. I don't know the area down there nor do I know a good company. I've...
  2. That is very odd that it would trip an overload...

    That is very odd that it would trip an overload fault but was a low pressure switch, must have been wired in series or somebody is reading the fault wrong.

    Kind of off topic here but I was where...
  3. Don't complain, put your nose down and work hard....

    Don't complain, put your nose down and work hard. I was 20 when I started at my company, it takes time and the other techs need to see your work before they will listen to ya. To them you're just...
  4. Replies
    19
    Views
    1,511

    Klein 11 n 1 is a must have for me, along with my...

    Klein 11 n 1 is a must have for me, along with my small fluke amp meter, leads, jumper wires, makita impact, strippers and a gauge with a small quick disconnect hose on it.

    I always end up with...
  5. Replies
    16
    Views
    1,272

    I had the same question when a coworker said TEET...

    I had the same question when a coworker said TEET too me for the first time, lol
  6. Replies
    16
    Views
    1,272

    Target Evaporator Exit Temperature

    Target Evaporator Exit Temperature
  7. Replies
    191
    Views
    9,626

    He had one laying around Cool

    He had one laying around Cool
  8. Replies
    191
    Views
    9,626

    I didn't think about that, lol

    I didn't think about that, lol
  9. Replies
    191
    Views
    9,626

    You aren't going to make many friends acting like...

    You aren't going to make many friends acting like that and posting unorganized post like you do.

    We use to have a guy like you at my company, he is no longer working for us. Salesman is what we...
  10. Replies
    15
    Views
    1,695

    That's why I don't like using aftermarket parts....

    That's why I don't like using aftermarket parts. we found out that a 3/4 HP universal motor(also from Johnstone) doesn't last long in a Carrier furnace.

    Edit: not all aftermarket parts are bad...
  11. Replies
    13
    Views
    1,323

    It goes between the furnace and indoor coil, it...

    It goes between the furnace and indoor coil, it limits the air temp coming into the coil.
  12. Replies
    13
    Views
    1,323

    Some turn the gas heat on during the defrost...

    Some turn the gas heat on during the defrost cycle, some turn the gas on and finish the heat cycle with gas. You can get a bonnet sensor and run both at the same time if you want.
  13. I love DDC controls and have self taught a lot of...

    I love DDC controls and have self taught a lot of what I've learned or went to classes. I started learning zoning back when I first started and got it down pat. I get sent on most of the zoning issue...
  14. Replies
    191
    Views
    9,626

    follow this^^^^^^

    follow this^^^^^^
  15. Replies
    16
    Views
    1,272

    I've got a Fieldpiece SRH2. It does RH, DP, WB...

    I've got a Fieldpiece SRH2. It does RH, DP, WB and DB. You can use the attached sensor or plug in a sensor. It works great and is pretty fast. I wasn't sold on Fieldpiece until this meter.
  16. Replies
    5
    Views
    519

    I've seen them have ohms in the hundreds and that...

    I've seen them have ohms in the hundreds and that becomes a voltage block, so the board doesn't get a full 24 volts back to the board.
    I'm assuming you are working on a condensing furnace. These...
  17. Replies
    5
    Views
    519

    restart the furnace, remove the wires from the...

    restart the furnace, remove the wires from the pressure switch and put your ohm meter on it, make sure its close to zero when closed. sometimes they can also close to quickly but i'm not sure of that...
  18. Replies
    18
    Views
    1,643

    I feel most of the new technology tools is making...

    I feel most of the new technology tools is making it so easy that monkeys can do it, which to me is a very low paid person with no experience doing the job I spent many months and thousands of...
  19. Replies
    18
    Views
    1,643

    Carrier also says everything has a 1/4 of 1%...

    Carrier also says everything has a 1/4 of 1% failure rate, I call b*ll$***
  20. Replies
    23
    Views
    1,710

    one thing I've noticed is that if you don't have...

    one thing I've noticed is that if you don't have that pilot assembly in there just right, it won't fire correctly. Thanks for your help. We are actually in the process of replacing the gun with a...
  21. Replies
    23
    Views
    1,710

    I've got the exact same issue with a power flame...

    I've got the exact same issue with a power flame gun.
    M#C3-G-20
    I dont have all the numbers on hand but we had a factory guy come out last April and he spent 4 hours checking everything and found...
  22. thanks for the info.

    thanks for the info.
  23. Replies
    28
    Views
    2,296

    I'd prefer to not say

    I'd prefer to not say
  24. the 120 seconds means this is how long it takes...

    the 120 seconds means this is how long it takes to go from fully open to fully closed. I've seen some actuators keep 24 volts on both the "close" and "open" teminals to keep it where it's currently...
  25. Replies
    13
    Views
    1,214

    True that

    True that
Results 1 to 25 of 132
Page 1 of 6 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event