Search:

Type: Posts; User: killeentech

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    1,761

    unmounted cap

    Go on service call behind a fellow tech that was there a couple times for a condenser breaker tripping. Bad part is the wires were long enough to reach factory cap mount.
  2. Replies
    7
    Views
    2,121

    Thanks for correcting pic . That is the front of...

    Thanks for correcting pic . That is the front of unit
  3. Replies
    28
    Views
    2,903

    I bet closest to end plenum are the coldest . (No...

    I bet closest to end plenum are the coldest . (No mixing chamber)
  4. Replies
    7
    Views
    2,121

    Rheem electric airhandler with cased evp stuffed...

    Rheem electric airhandler with cased evp stuffed in it still in case. I have seen to around town so far
  5. Replies
    28
    Views
    2,903

    No mixing chamber on plenum, if no duct leakage.

    No mixing chamber on plenum, if no duct leakage.
  6. Replies
    7
    Views
    2,121

    rheem with ICP cased evp

    Rheem evp is probly cheaper .. how do i rotate the picture ? Should be left side up
  7. Could it be compressor running in high pressure...

    Could it be compressor running in high pressure bypass . Had one onfirday we install in fall installers had close to 5 lbs of 410a to much. Homeowner said cooled great till it got 90 plus outside .
  8. Could it be in tstat settings " cycles per hour"?

    Could it be in tstat settings " cycles per hour"?
  9. Replies
    1
    Views
    474

    leak detector

    Anyone got one of this? Cps leak-seeker II. Any good or junk
  10. Replies
    1
    Views
    499

    You need a ARH4 head

    You need a ARH4 head
  11. What yall do with the direction leds on condenser...

    What yall do with the direction leds on condenser motors?
  12. Replies
    25
    Views
    2,527

    What is eddy effect?

    What is eddy effect?
  13. Replies
    20
    Views
    2,405

    It was explianed to me to use only oem start...

    It was explianed to me to use only oem start assits . Because 5 2 1 kit have a relay remove the stick on side it gives u a # ???-??? Which is voltage drop out. Which needs to match oem...
  14. Replies
    5
    Views
    1,691

    Because its a electric down flow moblie home...

    Because its a electric down flow moblie home unit. Usually the flex leads to roof and has a power open damper for fresh air. This are terrible for dirty evp coils be cause filter lay right on evp...
  15. Replies
    13
    Views
    2,959

    Some poeple have no pride

    Some poeple have no pride
  16. Replies
    12
    Views
    1,885

    Thanks frosty beer the picture is right now....

    Thanks frosty beer the picture is right now. Someone removed rheem mcoil and section and place goodman cased coil in it place. I was glad it was a sales call not a no cool call
  17. Replies
    12
    Views
    1,885

    Upflow

    Upflow
  18. Thread: crackheads

    by killeentech
    Replies
    4
    Views
    1,721

    crackheads

    Bids from last month copper must have been up . Can you tell plumbers missed closet with chase
  19. Thread: my luck

    by killeentech
    Replies
    9
    Views
    755

    More pic

    More pic
  20. Thread: my luck

    by killeentech
    Replies
    9
    Views
    755

    my luck

    For who wears rings at work.i aas soldering a tap ona window unit . Solder driped on my wedding ring and stuck i couldn't get it off till it cooled. It sucked to topto all off this happen on 4 30 12...
  21. Replies
    12
    Views
    1,885

    who thinks this up?

    Seen this on a sales call.the evp was a 2011. At first i had to pinch myself maybe i wasin a wall of shame twilight zone . Then i fist pumped in my head . Ihave to show my find off :grin2:
  22. Thread: RTU

    by killeentech
    Replies
    27
    Views
    2,708

    isnt this a forum for questions. Thanks...

    isnt this a forum for questions.
    Thanks jpaulsmith . I know very simple question just was never explained to me
  23. Thread: RTU

    by killeentech
    Replies
    27
    Views
    2,708

    RTU

    How long does a evp blower belt normaly last and how often should very be replaced?how tight shouldthe belt be ? Also how to check pulley alignment?
  24. Replies
    5
    Views
    761

    Smart thinkin .. i like

    Smart thinkin .. i like
  25. Replies
    23
    Views
    6,163

    Ihad a low pressure switch on a carrier hp that...

    Ihad a low pressure switch on a carrier hp that had a loose connection inside the switch . Caused contactor to chatter and fryed contacts.
  26. Replies
    23
    Views
    2,412

    If airhandler has evp coil on bottom i stick cell...

    If airhandler has evp coil on bottom i stick cell phone in filter slot and snap a few pictures and review. Saves alot of time and guess work. Coil above blower to easy to remove evp cover slideevp...
  27. Replies
    5
    Views
    880

    I second this

    I second this
  28. Replies
    16
    Views
    1,677

    I am pretty sure Time delay will work with a...

    I am pretty sure Time delay will work with a common or with batterys.
  29. Replies
    7
    Views
    744

    Open face coil ? Like in a down flow trailer...

    Open face coil ? Like in a down flow trailer house unit?
  30. Replies
    5
    Views
    642

    RGF ON CARRIER INFINITY

    How would one add a RGF to a infinity to run with fan not all time?
  31. Replies
    16
    Views
    2,616

    here today gone tomorrow

    I serviced 6 goodman 5 ton r22 heatpumps the next day they were all gone. From a church. Its a shame.no one is safe.
Results 1 to 31 of 37
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event