Search:

double chech rotatation wrong direction will cause higher amp draw. I know, been there done it

Primmer don t know where you're located. Internet search for beverage tubing or parts should get you going. Oeiter clamps can be found at same or Graingers Supply.

Distance from cold plate or...

:gah:Primmers this is a project if its your first install. Do you have acess to beverage parts? You're going to need about 200ft. of tubing (number of buttons on gun plus 2), Stainless steel...

Pez toy..can't begin to tell you how many open display cases, with refrigeration problems have been fixed by putting shelfs in correct order. Small at top larger at bottom. I'm seeing them more and...

Toptech you're the man thanks. Lost pages on a rainy day begruge buying another manual procrastination works. ez

one quick note on the freezer. A 25x25 is pretty large box. Assuming its a concrete floor with insullation underneath. I'd pull it down slow, allowing walls, floors etc. to reach temp 5 to 10 degrees...

baub excellent job on the video, better than some pro training I've seen. Precise, clear and clean,

cg2 is right. there is a bulletin avail. certain seris has bad motors. I've changed out two this winter. Found #3 today on a ac start up. Getting Trane to admit it is pretty hard though. First one...

A couple of points about co2
There's two types of tanks as stated b4 one has a siphon tube and will pull liquid the other doesn't and will pull gas.
Never use a tank from a beverage company. They...

Sounds like you finally got it dried out, and cleaned out. That was a lot of moisture. The end result of a bunch of top offs. Not finding the low side leak and just adding gas,gas gas. Those kind of...

Here's a couple more tidbits
There's also a single check valve on co2 line to prevent seltzer from backing up into co2 tank. When tank pressure drops below carbonator pressure.

Inside of tank...

ok if this is what I think it is you have an old fountain system in the order of a B and B i.e. a bastian and blessing. see if you can reference anything with that name. The copper line is water in....

This thread is the reason why I like this forum. Good and timely info. I've been doing this work for too long, and never seen a prep with a epr. One less surprise waiting for me. I'm not fond of...

Two things happened when I read this thread First I thought good initiative from a new tech and then all the little hairs on the back of my neck went up.

1 Call frymaster First b4 you do...

ok here's what you can do. open door, unplug coin mech ( large black plug ). then lift mech up off of slotted screw mounts. looking at top of mech you'll see 2 levers. one on each side lift up pull...

Joe seen them in markets small True pop cases. They use a residential defrost timer to reverse fan. Belive me it doesen't work. coil still blocks up might take a little longer ...

DOW seem to remember a sales rep going on about clarity of product at too low of temp. tends to get cloudy as I didn't have a good thermometer and was forced to use the taste temp method the...

sounds like you have a lopped evap. yes txv and epr set pressure control for an evap temp of 28 use pt chart per refrigerant. watch lite beer, first to freeze. check all insulation. Remember a 3 to...

ha !!! I know what you're doinn. 'cause I'm an old timer too.

a slurpee unit besides being expensive, really expensive, is labor intensive. I'd look on e bay, or someplace like that for a bunn, or ouligani(spelling sucks)counter top unit like you see in c...

fireye03 is right got same story from supply house. unregulated nitro tank. don't know what possed him to even think of doing it. he didn't sound like a rookie. 37 yrs. old 2 kids shame. this is a...

after all that you now have to plug the condenser back into the spider I carry a couple of short {24") AC extension cords. Pick them up at hardware store. Saves needing exta elbow.

yo r12 welcome to soda. sounds like you ended up looking like a punk rocker. Orange spiked hair and all. A sugesstion Refer supply houses carry vise grip pinch off pliers. Try them they have...

yo r12, funny, moreso 'cause been there done that. If it was a 7/11 how'd you get your feet to move in the goo? Don't know why you had to bribe a kid, been my experience they'll do anything to get a...

also agree with Mikey poe + 134 + heat= clogged cap. do't know what model you're working on but most of their reach ins are acessable from top a couple of screws and you can pull the evap up and work...