Search:

Type: Posts; User: rango

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    1,197

    I ended up jumpng up to a 1 hp5.2 amp and it's...

    I ended up jumpng up to a 1 hp5.2 amp and it's been fine for acouple of days.Thanx all.
  2. Replies
    19
    Views
    1,197

    Nope, 10 mf Cap circuit only running .70 amp

    Nope, 10 mf
    Cap circuit only running .70 amp
  3. Replies
    19
    Views
    1,197

    Since Larry retired, nobody at AAON knows...

    Since Larry retired, nobody at AAON knows anything about these old units unless you have the part number,and then it's just the part.
  4. Replies
    19
    Views
    1,197

    Coil clean,rpm correct. Label says original motor...

    Coil clean,rpm correct. Label says original motor was 6.75 amp.
  5. Replies
    19
    Views
    1,197

    Amp draw is just under plate value. seems like...

    Amp draw is just under plate value.
    seems like more air is necessary for cooling.
  6. Replies
    19
    Views
    1,197

    Condensor fan size/pitch question

    Hey Guys and Gals. Working on an old (35) AAON commercial unit. Condenser fan motor .75 hp as per data plate cuts out on thermal after about 45 min.
    Assume bad bearings even though amp draw not...
  7. Replies
    3
    Views
    1,203

    Wet brined in salt and brown sugar. Cookedm one...

    Wet brined in salt and brown sugar. Cookedm one in the oven and one in the vulcan convection oven/smoker in the garage. 30 people , no complaints, mmmmmoist.
  8. Replies
    13
    Views
    4,854

    Just hook an open on removal of power time delay...

    Just hook an open on removal of power time delay relay onto the on/off switch of the equipment.
  9. Replies
    11
    Views
    3,084

    Just a quick tip. Been working onMcD stuff 11...

    Just a quick tip. Been working onMcD stuff 11 yrs. Comp will act erraticaly if it gets too hot. SSR's won't stick but the ones in an hlz will half wave. They will pass either the high or low side of...
  10. Replies
    4
    Views
    1,311

    Hope you got this done. It's a PITA but I have...

    Hope you got this done. It's a PITA but I have tips for future if you need them.
    Rango
  11. Replies
    6
    Views
    2,418

    I haven't been around for awhile so this is late....

    I haven't been around for awhile so this is late. Quick way to check for computer problem, which this error can be is to switch the puter with the one nex t door to it.
  12. Replies
    9
    Views
    2,926

    Just an FYI for HOT-HI on MCD's fryers by...

    Just an FYI for HOT-HI on MCD's fryers by Frymaster. It means that the computer is reading a temp that is over the set point. First thing to check is whether or not the TC is covered with carbon...
  13. 6 Goose Island IPA's and just had a nice big bowl...

    6 Goose Island IPA's and just had a nice big bowl of Guiness Irish Stew. Bedtime now , gotta work in the morning
  14. Replies
    11
    Views
    12,549

    Anybody have a piping diagram for using an epr...

    Anybody have a piping diagram for using an epr with a low and medium tmp on one compressor? Where does the epr go in this scenario?
  15. Replies
    4
    Views
    598

    emerson hpc-5 vs. oroa-5

    Are there any problems with substituting an Emerson hpc-5 (which I have in the truck) w a sporlan oroa-5 (which is 3 days out at the supply house) on a walk-in 3-door cooler? Anybody have any...
  16. Replies
    12
    Views
    4,282

    ?

    ?
  17. Replies
    30
    Views
    2,091

    Some 17 yr. Old Texting Kid Just...

    Some 17 yr. old Texting Kid just... ran into the back of my parked Tracker Tundra which was hooked to my pick-up, and pushed it 5 feet forward and messedup a bunch of stuff and she's ok but somebody...
  18. Thread: Super Seal

    by rango
    Replies
    14
    Views
    2,332

    Same here. It has it's place. It's a tool and...

    Same here. It has it's place. It's a tool and just like any tool it shouldn't be used for all situations. Just because you have a hammer, every problem is not a nail, to paraphrase an old quote.
  19. Replies
    64
    Views
    2,450

    Heard a liberal on NPR (surprise) say that "...

    Heard a liberal on NPR (surprise) say that " George Bush's blah, blah on climate says that record snow and low temps will be part of the changes". First time I ever heard a liberal reference G.W.'s...
  20. Replies
    1
    Views
    347

    Obama Underwrites Offshore Drilling

    Wall Street Journal Article

    http://online.wsj.com/article/SB10001424052970203863204574346610120524166.html
  21. Replies
    23
    Views
    857

    Heard some business owner on NPR today say that...

    Heard some business owner on NPR today say that he watched the speech and was glad that Obama was back on track. Apparently folks can't tell the difference betwixt words and action. What and ignorant...
  22. Replies
    23
    Views
    857

    I am actually watching it and so far my favorite...

    I am actually watching it and so far my favorite part is when Harry Ried yawned.
  23. Replies
    42
    Views
    4,496

    I doubt anybody who hasn't been on a roof in -10...

    I doubt anybody who hasn't been on a roof in -10 to -20 temps at 2 in the morning would know what it takes to get the liquid to move into the system. Low wattage blankets won't work when the tmps are...
  24. Replies
    20
    Views
    715

    Definitely not a 2 party system anymore. It's one...

    Definitely not a 2 party system anymore. It's one party and 2 branches.
  25. Replies
    21
    Views
    971

    Don't know the answer to that, but I bet Canada...

    Don't know the answer to that, but I bet Canada didn't have a firmly etrenched insurance industry. The thing that they are arguing about is all smoke and mirrors. Health care has nothing to do with...
Results 1 to 25 of 386
Page 1 of 16 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event