Search:

Type: Posts; User: harley91

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    527

    Thank You So Much Have A Great Day

    Thank You So Much Have A Great Day
  2. Replies
    2
    Views
    527

    flaring/swival Tee on 410a?

    Have not worked on many 410a systems,Need to know if you can use a swival tee or is this a no no?And can you use flare fittingsin the high /low lines.have to install a water regulator,Johnson V246,No...
  3. Replies
    1
    Views
    1,228

    York ZB4K1 compressor Torque specs?

    Does anyone out there have the compressor Torque specs and clearances on a york ZB4K1 compressor? Thanks
  4. Replies
    11
    Views
    768

    Can't Humidity UP problem

    Have a 2850 sf 3 year old house,Installed a 9 gal per day true steam Humidifier,started up ,Running now for 3 weeks .Humidistat set at 40% can only get house to 32% out side temp between 10 and...
  5. Evacuation on chiller/Vac drops with pump off

    Hi
    had a situation ,pulled vac on centrifugal [no R11 in system]pulled down to 26 in ".Used 3 vac pumps.felt presure comming out of pumps,isolated pumps turned off pumps ,let sit ,had thermal...
  6. Replies
    7
    Views
    2,032

    Bad Suction Accumulator

    Has Anyone come acoss a bad suction accumulator? Not sure what can go wrong,Have a small chiller ,Floading back,low low load ,has accumulator,R22,suction 20lb,low temp compresor discus.Want to know...
  7. Replies
    7
    Views
    743

    Thanks,You guys are GREAT

    Time to buy a Halide
  8. Replies
    7
    Views
    743

    Sniffer for chiller bundle with glycal?

    I think I may have a leaking tube in a small chiller ,The water has glycal mix,I was told electronic detectors pick up glycal,is this true? If so what would you use to sniff for R22?



    ...
  9. Replies
    4
    Views
    487

    RTAA Chiller-270/370 Question (100*sec)

    What it definition of term - 100*seconds
    If entering water temp drops 2* below leaving water temp for more than 100* seconds - indicates loss of water through chiller evap.Thanks
  10. Replies
    1
    Views
    427

    Sanyo split problem with [temp control]

    Have a older sanyo split M#ch182 The temp is over shooting set set point [will not shut off]-you can shut unit off and on through remote.but remote will not auto turn off unit at setpoint. you must...
  11. Replies
    7
    Views
    618

    Hay guys I got the manual on machine from york, ...

    Hay guys I got the manual on machine from york, Cooler -Horizontal,flooded,shell and tube type,distrabution system consisting of -distribution trugh to give uniform distrabution throughout the shell...
  12. Replies
    7
    Views
    618

    Thanks Klove

    Thanks Klove
  13. Replies
    7
    Views
    618

    Tube Supports York YSDC Screw

    Does anyone know what the tube supports in the cooler and the condenser are made of are M#YSDCDBS3-CMCS?Thanks
  14. Replies
    11
    Views
    1,347

    HI GRAHAM Thank you very much ,That was a...

    HI GRAHAM
    Thank you very much ,That was a wonderfull Explanation.Sounds like that would be the best way to make shure its right.Thanks again
  15. Replies
    11
    Views
    1,347

    Thanks for the input chillr dude.That helps

    Thanks for the input chillr dude.That helps
  16. Replies
    11
    Views
    1,347

    Hi graham Thanks for your inpute! With out...

    Hi graham
    Thanks for your inpute!
    With out writing a book,I do know about moisture in the system and megging,Im not asking about any clean up issues.Ive cleaned up many systems ! I try to do things...
  17. Replies
    11
    Views
    1,347

    The oil tested low acidic,and it looks...

    The oil tested low acidic,and it looks dirty,sight glass is still green.I am megging motors This is a prosses chiller Cant Leave off long,trying to buy time.
  18. Replies
    11
    Views
    1,347

    RTAA screw Chiller-Changing oil & filters

    Does anyone have steps on changing oil on RTAA 370 air cooled screws-The book does not have info.
    Anyone done it out there?Thanks
  19. Replies
    312
    Views
    10,067

    new member having trouble postin question can you...

    new member having trouble postin question can you help harley91
Results 1 to 19 of 23
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event