Search:

Type: Posts; User: mickkassem

Search: Search took 0.01 seconds.

  1. Replies
    45
    Views
    4,035

    Optimal fan speed

    Interesting discussion and pertinent to something I have been trying to understand. We have a Trane TAM 8 air handler coupled with a XL20 two/four ton. We also have the nice Comfort color stat. The...
  2. Replies
    2
    Views
    499

    Heat Pump Comparison Outlet temps

    We have two Trane systems in a two story home. The upstairs unit in about six years old 3 ton that runs at one indoor blower speed summer and winter. The new unit downstairs is a Trane TAM8 with a...
  3. Replies
    2
    Views
    647

    Trane XL950 Stat, Defrost

    I checked the system when the defrost cycle ran and the airflow is at 100% with the TAM8 display showing HPD1 + EH with three black boxes. I know there has to be air flow during defrost but the air...
  4. Replies
    7
    Views
    897

    Software

    Thank you so much. I updated software with SD card. It did not update online but indicated it was up to date. It now has a screen that shows both the indoor and outdoor units are online. This has...
  5. Replies
    7
    Views
    897

    Software

    Software is up to date according to thermostat and all items show correctly on the advanced setup menu. I really hate to bother the installer over something so trivial. By the way the heater strips...
  6. Replies
    7
    Views
    897

    Sorry, I didn't mean to select the thumbs down...

    Sorry, I didn't mean to select the thumbs down icon. It looked like a question mark without my glasses. Not sure how to get rid of it.
  7. Replies
    7
    Views
    897

    Trane XL950 stat

    In the standard setup, there is a screen that asked for Indoor Unit Heat Stages. we have a TAM8 air handler with the 15 kW heat strips and the XL20i heat pump. Is it asking for stages of the heat...
  8. Replies
    7
    Views
    1,493

    Kind of obvious but just wanted to be sure I...

    Kind of obvious but just wanted to be sure I checked out everything before making the call. The HUM connection on the TAM8 circuit board is for the humidifer wiring - correct? Checked out your...
  9. Replies
    7
    Views
    1,493

    House humidity reading is 41% and set point is at...

    House humidity reading is 41% and set point is at 45%. I know the indoor reading is high but with that differential, the water valve on the humidifier should be energized - right? Thanks so much for...
  10. Replies
    7
    Views
    1,493

    Settings

    I looked at the Monitor Menu on the TAM8 when heat was on and reading was HUMIDIFIER-ON. I also checked thermostat and under HUMIDIFICATION, the settings were for control of INDOOR RH and...
  11. Replies
    7
    Views
    1,493

    Trane XL950 Stat

    We just had a Trane XL20i heat pump, TAM8 air handler and XL950 thermostat installed. Outside temps just cold enough to get the unit running yesterday.

    For humidification, does the XL950...
  12. Replies
    7
    Views
    1,383

    TAM7 Indoor Blower Timing

    We have our TAM7 set for ENHANCED MODE indoor blower timing where it ramps up and down. We seem to be using more electricity now than we did before when we had a SEER 12 A/C. Now we have the 20i...
  13. Replies
    45
    Views
    5,538

    Trane TAM8

    I was looking online but could fine no updated info about when the TAM8 air handler would be available. Do you have access to the Trane ComfortSite website that might provide updated information?
  14. Replies
    7
    Views
    1,383

    My Trane dealer said the TAM 8 will be out in...

    My Trane dealer said the TAM 8 will be out in late third quarter. Waiting for one now. Have the TAM 7 installed now.
Results 1 to 14 of 16
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event