Search:

Type: Posts; User: Fmech

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    579

    automated logic lost password

    have customer with no access to system
    engineer left and took/changed password on his way out


    can anyone point me towards a work around or security file extension ??
  2. Replies
    5
    Views
    1,006

    carrier 19XL high bearing temp

    Getting an occasional fault per the engineer
    have not seen his machine yet to check logs. going there monday
    possible causes???
    oil levels are good and temps are at 138 degrees
  3. Replies
    3
    Views
    1,032

    Trane PCM software

    Thanx for the quick response.

    would anyone have an e-mailable copy of that software out there???
    and do I need an interface or just cable direct hook up. I have the parallel
    to serial patch...
  4. Replies
    3
    Views
    1,032

    Trane PCM programming

    Have a job with a problem PCM I need to upload the program and load into a new PCM board. I already have trane tarcer Rover version but I am pretty sure its not capable of loading a PCM. Can...
  5. Replies
    12
    Views
    2,603

    I have a front end computer there that hasn't...

    I have a front end computer there that hasn't been in use for ???? who knows
    what would be the suffix for the b/u file??
    the front end does have the graphics how ever tried a serial cables hook...
  6. Replies
    12
    Views
    2,603

    alerton

    Actually, I have both a copy pf the software (ibex for windows) and the parallel port "key"
    More specifically, i was looking for some assistance as to what my laptop hook up would be....
    through...
  7. Replies
    12
    Views
    2,603

    perhaps I don't have the exact correct name for...

    perhaps I don't have the exact correct name for this module
    Its a wall mounted back lit LCD display module with up down left right and N & P keys for navigating around to the individual VLC's that...
  8. Replies
    12
    Views
    2,603

    alerton microset

    Could I also trouble you for the same info
    I have a alerton microset that lost its program and am looking to scan the buss and reload the points

    THANX!!!!!!!!!
  9. Replies
    2
    Views
    783

    comfortview software

    Most software has the ability to upload and copy an existing program set up out of an existing controller and then down load it to another controller on the network.
    is there a carrier publication...
  10. Replies
    2
    Views
    783

    carrier comfortview controller programming

    have several jobsites that I need to replace VAV box controllers &/or reprogram
    337cfan & VAV controllers. Can this be done through the comfortview front end
    on the network?? or do I have to...
  11. Replies
    153
    Views
    38,699

    [QUOTE=HVACRACbob;7352592]230.10-m1 (804) ???????...

    [QUOTE=HVACRACbob;7352592]230.10-m1 (804) ???????

    Is this top secret???????

    Out of 100+ People Begging]

    After your tirade can we assume that you would like a copy of that form
    If so,...
  12. Replies
    153
    Views
    38,699

    you just might want to redo your email address in...

    you just might want to redo your email address in your profile, It's wrong
    yes, I resent it to your correct email address
  13. Replies
    153
    Views
    38,699

    in your email

    in your email
  14. Replies
    13
    Views
    1,317

    High current amps resolved

    After a LOT of calling around FINALLY got the info I needed.
    To any and all who may have followed this thread the following is the answer.
    For the millenium recip chiller control.
    the following...
  15. Replies
    13
    Views
    1,317

    Any york factory tecs outthere??

    Still having a hard time getting to the bottom of where the machine gets the correct amp rating for the over current parameter on this YCAR chiller.
    If any of you readers have any thoughts. After...
  16. Replies
    13
    Views
    1,317

    Eprom question

    he chiller had been running okay (to my knowledge)
    the building engineer had gone up to reset the unit after a bad storm
    and apparently left the access door loose and got some (or all) of the...
  17. Replies
    13
    Views
    1,317

    The dip switch settings match. the current draw...

    The dip switch settings match. the current draw (combining both wires for each phase is 71 + 72 = 143 though only one wire from each phase goes through the current sensor and one does not, as I...
  18. Replies
    13
    Views
    1,317

    its a split feed 2 wires per leg one each goes...

    its a split feed 2 wires per leg one each goes through the klixon and one does not
    I measured the 3 (separately) that go through and the three that don't
  19. Replies
    13
    Views
    1,317

    YORK YCAR0230 current sensor reads 50% to high

    I have a YCAR0230sc46P aadb SN RBKM6505AA
    unit is locking out on over current high amps reading of 160% @ 164 amps. The problem is that I'm reading 71 amps actual on all six feeders to compressor...
  20. Replies
    6
    Views
    1,273

    Just a FYI Update> Went to this job today and...

    Just a FYI Update>
    Went to this job today and the board is slowly fading into the sunset.
    I now have no access other than status, but, the good news is that when i was there yesterday I was able...
  21. Replies
    6
    Views
    1,273

    thanx for the response... before I get back over...

    thanx for the response...
    before I get back over there when I hit program does it normally prompt for
    for that password (cause this display currently does not) or when "program" is on the...
  22. Replies
    6
    Views
    1,273

    York YCAJ Millenium Can't Change FL Amps

    York Semi Hermetic YCAJ 0140 I can't change the full load amp settings The chiller starts and runs on both circuits but the chiller locks out on high current . when I hit the current button it...
  23. Johnson M3 graphics Set up button to display schedule

    I need someone in Johnson land for this. I have a m-3 Graphics GDF display
    I want to add a button to basically execute minspecter and then open up the schedule file for that piece of equipment...
  24. Replies
    153
    Views
    38,699

    in your email

    in your email
  25. Replies
    14
    Views
    1,815

    just saw that you have this 230.10.m1 info I was...

    just saw that you have this 230.10.m1 info I was looking for
    could I possibly trouble to send it to one more guy?? My email is Removed
    I have a ycas 160 that we put in a new compressor 2 years ago...
  26. Replies
    153
    Views
    38,699

    does anyone have a copy of the bulletin for the...

    does anyone have a copy of the bulletin for the YCAS unloading Issues troubleshooting?
    form 230.10-M1 (804)
    can you email to Email Address Removed
    thanx!!!
  27. Replies
    14
    Views
    1,978

    thanks much for the reference sheet greatly...

    thanks much for the reference sheet
    greatly appreciated!
  28. Replies
    14
    Views
    1,978

    10 w 40? nice answer...

    10 w 40?
    nice answer...
  29. Replies
    14
    Views
    1,978

    same thing to me the final insult from york is...

    same thing to me

    the final insult from york is that they charge like50-60 dollars for shipping & handling on smaller orders ( I can't wait to see the bill for 45# of oil!!! )
    I had them ship a2...
  30. Replies
    14
    Views
    1,978

    OK I gave up and ordered it from york in...

    OK I gave up and ordered it from york in baltimore
    (via slow boat from china)
    thanx to y'all for the input anyway
    WHAT an incredible pain in the butt!!!
  31. Replies
    14
    Views
    1,978

    I need the specific viscosity like emk 68 or??...

    I need the specific viscosity
    like emk 68 or?? artic etc
    its for a change out that I want to replace the oil
  32. Replies
    14
    Views
    1,978

    oil type needed for YCAS york compr

    can someone point me at the correct oil for a york ycas 160EC chiller with screw compressors DX536lasa17
    It is a R-22 machine
    I prefer getting this back running and not have to wait for it to ship...
  33. Replies
    18
    Views
    1,337

    update

    under the heading of when it rains it pours>>
    got there today and noticed that the terminal lug mount on the 400 amp contactor had burnt up and (of course) not repairable. so overniting new...
  34. Replies
    18
    Views
    1,337

    absbr

    Thanx much for all the info
    I believe it has 3 heads
    as I said I'll be there later I'll let ya know what I find, FYI (and mine)
    thanx again..
    dave
  35. Replies
    18
    Views
    1,337

    to absrb

    thanx, sorry this is dragging out so long nodded out doing some proposals
    I understand the discharge valve leaking would push out the oil but if the suction valve is bad what effect would that have...
  36. Replies
    18
    Views
    1,337

    adsrb..

    after thought # 87.....
    would a bad valve cause pump out of oil??
  37. Replies
    18
    Views
    1,337

    astrk & powell

    no, OEM York model J semi hermetic's
  38. Replies
    18
    Views
    1,337

    to powell

    What you described is pretty much what happens.
    I'm curious, if this is the case and its pressurizing the crankcase call me stupid but where is the oil leaving the compressor?? Is it blowing past...
  39. Replies
    18
    Views
    1,337

    oil pressure loss

    York YCAJ Chiller--Semi hermetic
    I've got an odd one here compressor locks out on oil pressure after running 5-10 minutes
    work done to date: pulled and weighed in correct charge proper oil levels...
Results 1 to 39 of 39
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event