Search:

Type: Posts; User: J-Fish

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    256

    Compressor identification

    H23A423ABCA

    I am thinking it is 42,000 btu? Tag is long gone on the unit.

    Thank you,

    J
  2. Replies
    24
    Views
    4,450

    This was in a 10 ton Trane. Stupid tech before...

    This was in a 10 ton Trane. Stupid tech before me couldn't buy a clue.

    Found the short, re-insulated the wire and put a 3 amp back in her.
  3. Replies
    24
    Views
    4,450

    What's wrong in this pix???

    Hello! Really?
  4. Here is the pix...

    Here is the pix...
  5. I sure will tomorrow. Yeah, most everything I...

    I sure will tomorrow. Yeah, most everything I run across can be searched by the first 4 prefixes of the model number. I should say, at least you will come up with something. But I get nothing with...
  6. Help finding paperwork/data on cooler condenser

    Hey, I am in need of a speck sheet or install manual (or anything else) I can find on the following:

    Brand? -- HTP
    Mod -- HTLH15H22P-E
    Ser -- H02187977-0104

    Thanks for any and all...
  7. Replies
    15
    Views
    1,365

    Maybe I should say, "Hand Truck" for you guys...

    Maybe I should say, "Hand Truck" for you guys that don't play with dollies!
  8. Replies
    15
    Views
    1,365

    Dolly questions...

    I know that we all fight moving condensers back and forth, but does anyone have any tips or tricks they would like to share? Any dolly configerations that work great?

    J
  9. QDO452A lbs per day rating at 100 & 90 degrees days

    Can anyone find a rating on the above ice machine. My books don't go back that far.

    J
  10. Thread: Scotsman CME256

    by J-Fish
    Replies
    6
    Views
    2,066

    Fellows, just wanted to say thank you to all...

    Fellows,

    just wanted to say thank you to all that posted. Had to replace the eyes and went ahead and did the thermistors just for good measure. The eyes had me thinking back-wards as what the...
  11. Thread: Scotsman CME256

    by J-Fish
    Replies
    6
    Views
    2,066

    I have been reading up on the model and from what...

    I have been reading up on the model and from what you say Tiger, when the bin is full you will have a solid green light. When the ice starts to fall the green light blinks.

    Now, how can I test my...
  12. Thread: Scotsman CME256

    by J-Fish
    Replies
    6
    Views
    2,066

    Scotsman CME256

    I am working on a Scotsman CME256. When it starts up the sequence is Hot Gas Valve off (refrigeration) then a few seconds later, the hot gas valve opens. Runs for a few min and then cuts off with...
  13. Replies
    10
    Views
    1,234

    Combustion Efficiency Analyzer

    How many use them and do they stay accurate for long?
  14. Replies
    15
    Views
    1,417

    All valid points. One detail that I forgot to...

    All valid points. One detail that I forgot to mention is that Circuit A on my chiller was setting at about 15 psi suction pressure and 75 high side. It is why I started looking for a leak. I...
  15. Replies
    15
    Views
    1,417

    Chiller leaking in the barrel

    Chiller leaking in the barrel.

    If I suspect that my chiller is leaking R22 into the water loop, how can I prove this?

    I tried to use my sniffer, but it also went off due to the chemicials added...
  16. Replies
    6
    Views
    1,025

    Len, do the drop in replacements react at the...

    Len, do the drop in replacements react at the same pressure points so that you could weigh in a charge or charge by amp draw, of do you just charge and look for that 20 degree core temp?

    Or do you...
  17. Replies
    16
    Views
    2,569

    airdata870, that is exactly what I was looking...

    airdata870, that is exactly what I was looking for. Funny, they were one of the first places I called and they were not able to help me. Guess they are only as good as the knowledge they posses of...
  18. Replies
    16
    Views
    2,569

    You can get multi tap motor controllers and or...

    You can get multi tap motor controllers and or temp sensor and pressure controllers at the parts house but not rheostats, but these are single speed motors.

    The rheostat system worked well with...
  19. Replies
    16
    Views
    2,569

    Their in a old county building. Most of them are...

    Their in a old county building. Most of them are running just fine, but a few are over blowing the registers and making too much noise, causing complaints in courtrooms, etc.

    All motors are 277...
  20. Replies
    16
    Views
    2,569

    277 volt fan powered box rheostat

    277 volt fan powered box rheostat. I don't even know if I am spelling it correctly....

    Anyway, I have about 40 dual fan powered boxes that run single phase 277 volt motors. The original...
  21. Replies
    6
    Views
    1,025

    What would be the desired evaporator temp to...

    What would be the desired evaporator temp to achieve the 36-40 deg box temp? 25 deg once the heat load was removed?

    Can you charge by amps even if you go with a drop in substitute?
  22. Replies
    6
    Views
    1,025

    Coke Machine Help Needed

    If I want my frosty beverage to be in the 36-40 deg. range what temp should I be looking for in my evaporator?

    I am working on a 12-20 year old machine that the county owns and was trying to top...
  23. Replies
    3
    Views
    1,094

    Fluke 1587 insulation tester???

    Anyone try the new 1587 insulation multi meter from Fluke?

    I am looking to better my Megohm meter. Any feedback is appreciated.
  24. Replies
    7
    Views
    1,720

    Ok, all sounds good but is there a book to buy...

    Ok, all sounds good but is there a book to buy (Where?) or do you have to get with one of those consulting firms online. I am a small guy just trying to figure out where I need to be to be in the...
  25. Thread: Load calc

    by J-Fish
    Replies
    6
    Views
    610

    Eggman, email it to Jason @ LaFitte dot us and I...

    Eggman, email it to Jason @ LaFitte dot us and I will give it a try. I will not say that I am the master of the art but I am learning.
Results 1 to 25 of 259
Page 1 of 11 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event