Search:

Type: Posts; User: shanika

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    1,073

    I did as Marter suggested. Terminator tested...

    I did as Marter suggested. Terminator tested good. Is the defrost timer a possibility? Or should I test the heater again and try and figure out how many ohms is normal?
  2. Replies
    7
    Views
    1,073

    Checking the terminator is a little difficult for...

    Checking the terminator is a little difficult for me . By removing the ice I probably heated the terminator to the point that it's open if it wasn't anyway.
    The heater is not open but I don't know...
  3. Replies
    0
    Views
    275

    Defrost terminator or defrost heater?

    My domestic refrigerator /freezer coil started freezing up. I defrosted with the hair dryer and that lasted a week.
    The heater is not open. Don't they usually fail open? I jumpered the terminator...
  4. Replies
    7
    Views
    1,073

    Defrost terminator or defrost heater.

    What's the most likely guys? Coil freezing up, defrost timer working. I jumpered the terminator to test if it continues to freeze over. Sound like a plan?
    This is just a domestic freezer/...
  5. Replies
    2
    Views
    404

    I hope you are correct . I'm still not ready to...

    I hope you are correct . I'm still not ready to turn it off right now. It takes me about 10 days to get parts, thats a long time when you don't know you ordered the right part when the temp. is in...
  6. Replies
    2
    Views
    404

    Mr slim stat problem? Help please.

    Mr remote thermostat is having issues.
    I get no response from the unit. The time is working on the remote and when I reset it it seems to "boot up".
    None of the other buttons seem to have any...
  7. Replies
    7
    Views
    616

    Hey, I enjoy a challenge too but this was my...

    Hey, I enjoy a challenge too but this was my unit. It's just more fun when it's not 90 degrees and the wife is not on my back.
    The thermistor thing was about 50-50. Book suggested bad board and...
  8. Replies
    7
    Views
    616

    Rant about all the computerization.

    The MR SLIM unit I have been working on has really got me going.
    It failed and the coded alarm said "condenser unit failure". Wrong. Turned out to be the evaporator thermistor bad.
    In the good...
  9. Replies
    11
    Views
    3,329

    Now I have another question...... I bought a...

    Now I have another question......
    I bought a can of Cal-spray from the supply house.A no-rinse coil cleaner, i'm still reluctant to use it, don't want to take any chance that it will eat anything...
  10. Replies
    11
    Views
    3,329

    Well, I rigged up a 2 foot piece of copper on end...

    Well, I rigged up a 2 foot piece of copper on end of air hose and getting tons of stuff off the blower wheel. There is small gap under the coil that gives 1/4 inch access.
    And discovered nothing...
  11. Replies
    11
    Views
    3,329

    It's a real difficult task to pull the blower...

    It's a real difficult task to pull the blower wheel on this unit. Compounded by the fact that it is 10 foot off the floor. I'm gonna clean the coil tomorrow.
  12. Replies
    11
    Views
    3,329

    I think I agree now that it is dirt and not mold....

    I think I agree now that it is dirt and not mold. When I fired it up the first time this year it spit out stuff the first day. I don't think mold had time to grow yet.
  13. Replies
    11
    Views
    3,329

    Assuming the coil is dirty. Is there a particular...

    Assuming the coil is dirty. Is there a particular evap coil cleaner you can recommend?
    I'm a retired refrigeration mechanic and have been out of the loop .Thanks
  14. Replies
    11
    Views
    3,329

    Mr slim mold problems

    Started last season spitting out black balls of mold(I assume). I figured if it was mold sitting for 8 months would kill it off. As soon as I fired it up this year it starts putting out the stuff...
Results 1 to 14 of 14
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event