Search:

Type: Posts; User: TrueMech

Search: Search took 0.01 seconds.

  1. Replies
    45
    Views
    7,088

    Id be interested as well if you develop these!...

    Id be interested as well if you develop these! Keep us updated!!
  2. Replies
    6
    Views
    475

    Any update on this @Junior1983 ? Did you get this...

    Any update on this @Junior1983 ? Did you get this resolved??
  3. Replies
    6
    Views
    475

    Do you have a laptop loaded with the Carrier...

    Do you have a laptop loaded with the Carrier Field Assistant software and have the usb link to connect to the Rtu Open board?
  4. Replies
    6
    Views
    475

    You could try ohming out the sensors to make sure...

    You could try ohming out the sensors to make sure they correspond with the readings carrier has on the chart. 33ZCSENSAT. 642251 Also have you checked out the readings with Field Assistant straight...
  5. Replies
    37
    Views
    2,962

    Yes i use my impact for sheet metal work non stop...

    Yes i use my impact for sheet metal work non stop and it works great. Round sheet metal it works well in also as long as the sheet metal is heavier gauge, when its light gauge sheet metal on lets say...
  6. Replies
    37
    Views
    2,962

    I use the Makita 18v brushless impact and love...

    I use the Makita 18v brushless impact and love it! Very light weight and battery lasts very long. Has a nice clip on the side to latch on to my jean pocket or tool pouch when doing sheet metal. 641301
  7. Replies
    8
    Views
    1,868

    I believe they are carbon air filters for...

    I believe they are carbon air filters for removing gases and odors my friend.
  8. Replies
    18
    Views
    3,793

    We had the same problem on a 15 ton Carrier...

    We had the same problem on a 15 ton Carrier split, we cleaned the evap coil with cal-brite and rinsed her down. Condensate drains properly now, we had water everywhere on the inside before hand. I...
  9. Replies
    26
    Views
    3,989

    We have a few 5 ton yorks that we have just found...

    We have a few 5 ton yorks that we have just found that were flat on R22. We switched it over to M099 and so far so good. This is our procedure from now on to switch the smaller equipment over as it...
  10. Thread: Sheet metal

    by TrueMech
    Replies
    7
    Views
    1,111

    I second this book. I have it sitting in our shop...

    I second this book. I have it sitting in our shop for a reference guide for when needed. Shows you mostly all fittings you would need to fabricate and more. On a small scale of course but the...
  11. Replies
    26
    Views
    3,989

    Thats right, because the rubber ones swell with...

    Thats right, because the rubber ones swell with r22 and dont with MO99 if im not mistaken.
  12. Replies
    26
    Views
    3,989

    Thanks guys!!

    Thanks guys!!
  13. Replies
    26
    Views
    3,989

    Did you change anything special on the semi...

    Did you change anything special on the semi besides schraders, driers, suction and discharge gaskets when you were doing the conversion?

    Sent from my iPad using Tapatalk HD
  14. Replies
    26
    Views
    3,989

    MO99 and semi hermetics

    Anybody tried this conversion from r22 to MO99 yet on a semi hermetic?? Carrier M# 48EJE034-610DB
    Ive talked to Carrier and they tell me it can only be done by their techs for commercial equipment...
  15. Replies
    23
    Views
    3,889

    For a typical heating clean and check, we include...

    For a typical heating clean and check, we include it in our price. Its a safety issue if the customer has a cracked heat exchanger.
  16. Thread: Duct issues

    by TrueMech
    Replies
    9
    Views
    2,328

    Wow!! Looks like a dog got in the crawl and went...

    Wow!! Looks like a dog got in the crawl and went to town!!
  17. Thread: airflow

    by TrueMech
    Replies
    14
    Views
    2,516

    I love all the extra info!! Thanks

    I love all the extra info!! Thanks
  18. Thread: airflow

    by TrueMech
    Replies
    14
    Views
    2,516

    Could you send them to me also Dandy?? Thank you...

    Could you send them to me also Dandy?? Thank you very much i appreciate it!!
  19. Thread: Carrier RTU

    by TrueMech
    Replies
    24
    Views
    4,573

    Is the customer trying to economize and...

    Is the customer trying to economize and mechanical cooling is coming on or trying to heat and mech cooling coming on??
  20. Thread: Fancy Tee

    by TrueMech
    Replies
    3
    Views
    1,383

    Fancy Tee

    337201 Really?!?! I couldnt believe it when i saw this today!! All duct runs in full on flex and this is the tee they used to divert airflow.
  21. Replies
    6
    Views
    1,962

    I ran into this same exact issue with a...

    I ran into this same exact issue with a mitsubishi mini split and we found out it was a stuck exv and had to replace the coil in the head.
  22. Replies
    3
    Views
    1,041

    Excellent!! Im going to grab these asap!! Thanks

    Excellent!! Im going to grab these asap!! Thanks
  23. Replies
    16
    Views
    3,412

    That looks like its Midwest Helicopter. We used...

    That looks like its Midwest Helicopter. We used them for a helicopter lift at Woodfield Mall in Schaumburg, IL .We swapped a couple 20 tons out and removed some abandoned units all in about 20 mins!!
  24. Replies
    55
    Views
    33,806

    I have HVAC Load Plus for doing load calcs on my...

    I have HVAC Load Plus for doing load calcs on my ipad, and the same company has just released a new hvac load calc program for ipad that is used for light commercial and residential load calcs. Its...
  25. Thread: Hey Guys

    by TrueMech
    Replies
    3
    Views
    1,594

    Thanks!! I agree, its an excellent forum and im...

    Thanks!! I agree, its an excellent forum and im excited to be a part of it!!
  26. Thread: Hey Guys

    by TrueMech
    Replies
    3
    Views
    1,594

    Hey Guys

    Hello everybody!! Im pretty new to this forum but have been following it for a while now. My name is Steve and am an hvac technician from the suburbs of Chicago. Mostly commercial and industrial...
Results 1 to 26 of 43

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Comfortech 365