Search:

Type: Posts; User: chibulls21

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    2,414

    I hope the fan motor never goes out, or you ever...

    I hope the fan motor never goes out, or you ever have to get to the compressor!!! hahaha
  2. Replies
    28
    Views
    2,093

    Yeah, you had to have wired it wrong bro. I just...

    Yeah, you had to have wired it wrong bro. I just replaced a compressor for a heat pump that had a blown dual cap and start cap with a shorted relay. Cuased compressor to short eventually. When you...
  3. Replies
    74
    Views
    6,403

    If you reading 5.4 micro amps thens its obviously...

    If you reading 5.4 micro amps thens its obviously not the sensor. You need to make sure you have 24 volts at the valve and the work backwards to see where your losing voltage. Is this lp or nat?
  4. Replies
    99
    Views
    13,298

    I have two circumstances in the first year I...

    I have two circumstances in the first year I started service. First one, I was checking a cap on an indoor blower and the breaker to the elec furnace was labled wrong. So, instead of checking with my...
  5. Replies
    18
    Views
    1,363

    Whatever you do, make sure they teach you how to...

    Whatever you do, make sure they teach you how to work on hydronic and steam boilers. There are a ton of those in residential. Make sure they teach you how to work on the lennox pulse and make sure...
  6. actually, I take that back. It would depend on...

    actually, I take that back. It would depend on how long the pressures started to regulate after startup. If the suction pressure started going down immediatley, you might not have had enough but...
  7. Wow 866? Thats insane. How long is the lineset?...

    Wow 866? Thats insane. How long is the lineset? This is a dumb question but are you sure you installed the txv correctly? suction bulb in the right position and insulated? Do you have a biflow drier?...
  8. Thread: Final ?

    by chibulls21
    Replies
    5
    Views
    1,061

    I hate wall mount heat pumps in general! haha.

    I hate wall mount heat pumps in general! haha.
  9. Thread: Final ?

    by chibulls21
    Replies
    5
    Views
    1,061

    Well, geocomfort is good but it comes down to the...

    Well, geocomfort is good but it comes down to the installer. Whats the warranty on either brand? For example years on parts and labor?
  10. yeah, your going to have to test the cap. not...

    yeah, your going to have to test the cap. not telling you how. What is the amp draw on the motor? It might not even be the motor, could be alot of things. Did you say the outdoor unit is cutting out?
  11. Make sure you get a c&d shrader core tool. ( they...

    Make sure you get a c&d shrader core tool. ( they come in handy this time of year) Something to clear orffices. I' would get a type k temp clamp for your meter, it saves time. Get a open end...
  12. Screw the reefer side as far as an apprenticeship...

    Screw the reefer side as far as an apprenticeship goes. Get in on the pipefitting side, you'll make more money but the work sucks worse. I'am on the reefer side and often question about the whole...
  13. Replies
    16
    Views
    5,079

    Depending on if its a split geo either way, no...

    Depending on if its a split geo either way, no guages on a geo untill you check the gpm and td. That will tell you most of everything on a geo or if you have to check the charge. Performing those...
  14. Replies
    24
    Views
    2,974

    Na, close! It's more like, "whatever you do, deny...

    Na, close! It's more like, "whatever you do, deny everything"!
  15. Replies
    16
    Views
    5,079

    Did he do a gpm flow rate test and all that other...

    Did he do a gpm flow rate test and all that other necessary stuff? Shouldn't be putting on gauges untill absolutley necessary. Maybe flush the lines or check methanol mixture. Seem definitley...
  16. Replies
    24
    Views
    2,974

    Fake it untill you make it!!!!!! hahahaha! works...

    Fake it untill you make it!!!!!! hahahaha! works only for a few!
  17. In my local if you want to do service, you have...

    In my local if you want to do service, you have to get your own job with a contractor and then they get you in. same with install guys. If you get in the biulding trades side, thats where you'll work...
  18. Replies
    22
    Views
    1,196

    If you pump it down, just make sure you do the...

    If you pump it down, just make sure you do the right things putting it back together. Thats where you should be asking the questions! Even though I dought you'll get any answeres. I think I'd get the...
  19. Replies
    43
    Views
    18,548

    Goodman usually has a ten year warranty on...

    Goodman usually has a ten year warranty on everything if im not mistaken. Carrier sometimes has five year parts or labor and sometimes they have ten on both. Goodman is definitley cheaper but, they...
  20. Replies
    39
    Views
    8,494

    Impressive pics. We've had an increase with...

    Impressive pics. We've had an increase with copper thievery in our area as well.
  21. Replies
    16
    Views
    1,117

    What about corey and trevor? Them damn...

    What about corey and trevor? Them damn samsquanches!
  22. Replies
    16
    Views
    1,117

    Only other then bob and doug, maybe the members...

    Only other then bob and doug, maybe the members of "THE BAND"!
  23. Replies
    2
    Views
    609

    Well theres alot of them out there. The duct has...

    Well theres alot of them out there. The duct has to be that way due to the high velocity fan of course. I wouldn't worry about fibers. The main thing is making sure to look over the configuration of...
  24. Replies
    6
    Views
    773

    No DIY here.

    No DIY here.
  25. Replies
    5
    Views
    639

    Always good to check reversing valve of course....

    Always good to check reversing valve of course. Givin that the spring check, most reversing valve coils are energized in the cooling mode. most.
Results 1 to 25 of 37
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event