Search:

Type: Posts; User: jug_may

Search: Search took 0.00 seconds.

  1. Thread: Angle Driver

    by jug_may
    Replies
    8
    Views
    710

    After breaking a couple of the Milwaukee ones...

    After breaking a couple of the Milwaukee ones from HD, I got one of these.
    ...
  2. Replies
    31
    Views
    5,819

    For broken bolts that are not too rusted in I...

    For broken bolts that are not too rusted in I like to use a left twist drill bit to drill them out. Many times just the drilling force will be enough to back to broken portion out. Otherwise heat...
  3. Thread: duct stapler

    by jug_may
    Replies
    6
    Views
    1,143

    I don't have one, and don't know if they are made...

    I don't have one, and don't know if they are made in China but this looks like the same model that you have.

    Markwell
    ...
  4. Replies
    12
    Views
    851

    I've used them when putting stainless behind...

    I've used them when putting stainless behind kitchen hoods and needing to cutout for gas lines. They worked great for that, but haven't used them for much else.
  5. Replies
    12
    Views
    851

    A guy I worked with used the bits from Harbor...

    A guy I worked with used the bits from Harbor Freight. I said try my Lenox and he almost pushed the drill thru the duct. The first lenox that I had lasted 8 years until someone else thought they...
  6. Thread: Angle Grinders

    by jug_may
    Replies
    14
    Views
    1,856

    For the 4 1/2" and 6" grinders I've used Metabo's...

    For the 4 1/2" and 6" grinders I've used Metabo's for the last 8 years, Never a problem with them. I really like the variable speed 6" ones. Also have used Bosch 4 1/2", but they don't seem to run...
  7. Thread: air/acetylene

    by jug_may
    Replies
    34
    Views
    3,880

    Here is an article talking about acetylene saftey...

    Here is an article talking about acetylene saftey

    http://www.thefabricator.com/article/safety/fuel-your-safety-knowledge

    Most welding books talk about the 1/7th per hour rule.

    I think that...
  8. Replies
    26
    Views
    1,644

    I was taught to turn off the oxy first. If there...

    I was taught to turn off the oxy first. If there is any soot in the tip and/or splatter on the tip, by turning the fuel off first the excess oxygen can cause the fuel inside the tip to ignite. ...
  9. Thread: air/acetylene

    by jug_may
    Replies
    34
    Views
    3,880

    I've brazed 2" with an A-14 tip, it's loud as can...

    I've brazed 2" with an A-14 tip, it's loud as can be though. I carry an oxy/act setup with a b-tank and an R-40 Oxy for bigger jobs and the MC / R for smaller jobs. Have adapters from b to mc and...
  10. Thread: Hammer Drill

    by jug_may
    Replies
    21
    Views
    1,514

    http://www.dewalt.com/us/products/tool_detail.asp?...

    http://www.dewalt.com/us/products/tool_detail.asp?productID=14933

    I use one of these for sds bits. It works great putting anchors in above drop ceilings etc. Wish it could do chip only. I got...
  11. Replies
    12
    Views
    2,345

    Milwaukee M12 PVC cutter

    Anyone using one of these:

    http://www.milwaukeetool.com/ProductDetail.aspx?ProductId=2470-21&CategoryName=SC%3a+M12+Cordless+System

    Couple guys at work say this is the best thing since sliced...
  12. Replies
    15
    Views
    1,382

    I haven't used mine on soft copper. However it...

    I haven't used mine on soft copper. However it works great on hard copper. Mine had a tendency to walk on 1 1/8, but after a couple of cuts you get the idea of how to keep if from doing that. No...
  13. They work good to straighten out dented fittings....

    They work good to straighten out dented fittings. You know, the ones that someone dropped the put back on the shelf.
  14. Replies
    24
    Views
    2,321

    Around here they want you to use purple primer...

    Around here they want you to use purple primer because too many people were using the clear cleaner as a primer.

    The clear cleaner will help clean up purple drips on some surfaces. The best thing...
  15. Replies
    12
    Views
    1,249

    I picked up one of these a few weeks back to try...

    I picked up one of these a few weeks back to try it out. Used it putting in baseboard convectors. Works real good in hard to reach areas. Lots faster than using the imps. It works best on the...
  16. Thread: City multi

    by jug_may
    Replies
    4
    Views
    701

    Most of the time our Mitsubishi rep shows up at...

    Most of the time our Mitsubishi rep shows up at some point during the startup.

    When we installed the TG-2000 software and setup the GB50 controllers he had all the passwords to get us up and...
  17. Replies
    198
    Views
    63,224

    The CLC 1539 works good for everything that I do.

    The CLC 1539 works good for everything that I do.
Results 1 to 17 of 18
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event