Search:

Type: Posts; User: Juleous

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    102
    Views
    14,101

    Being your a new tech some info would help a lot....

    Being your a new tech some info would help a lot. Any line to another line should give the same readings resistance wise no matter what line to what line. The reading would be somewhere likely around...
  2. Replies
    24
    Views
    5,186

    Started 4 30 Ton units this summer, two had came...

    Started 4 30 Ton units this summer, two had came from the factory with leaks in the coils. Both tube sheet one evaporator and one condenser, real pain in the butt to find very windy which made it...
  3. Thread: My Supper

    by Juleous
    Replies
    9
    Views
    739

    Who cooks steak in a pan, that meat is meant for...

    Who cooks steak in a pan, that meat is meant for a BBQ.
  4. Thread: Newbie here

    by Juleous
    Replies
    41
    Views
    2,298

    Clean the outdoor coil.

    Clean the outdoor coil.
  5. Thread: Newbie here

    by Juleous
    Replies
    41
    Views
    2,298

    Clean the blower.

    Clean the blower.
  6. Thread: Newbie here

    by Juleous
    Replies
    41
    Views
    2,298

    Clean the indoor coil.

    Clean the indoor coil.
  7. Not really asking too much anyone in Canada could...

    Not really asking too much anyone in Canada could do it.
  8. Thread: Newbie here

    by Juleous
    Replies
    41
    Views
    2,298

    Change the filter.

    Change the filter.
  9. Replies
    13
    Views
    2,299

    I have shut down a few, one guy had another...

    I have shut down a few, one guy had another company come out and turn it back on. We had the inspector come out and he freaked out, the guy that turned it back on lost his ticket for a period and the...
  10. #2

    #2
  11. Replies
    10
    Views
    1,019

    I have pulled out the High Temp in a Jam before.

    I have pulled out the High Temp in a Jam before.
  12. Replies
    15
    Views
    3,053

    What is the treatment situation? To much chem? I...

    What is the treatment situation? To much chem? I have not run into this before just a guess.
  13. That would have hurt, did you get burned? I had a...

    That would have hurt, did you get burned? I had a schrader blow out on me one time burned my hand pretty good.
  14. Replies
    27
    Views
    2,478

    Is that a serious suggestion? Inspection with a...

    Is that a serious suggestion? Inspection with a scope or mirror, Smoke test, I have also closed all supply registers and watched the flame change. Lots of ways to check best is to remove the blower...
  15. Replies
    15
    Views
    1,011

    Push the mode button on the thermostat till it...

    Push the mode button on the thermostat till it say Emergency Heat, leave it set for what ever temp and then turn the breaker back on.
  16. One time I was servicing a Magic Pack unit by...

    One time I was servicing a Magic Pack unit by Armstrong, had the burner out and cleaned it put it all back together and forgot to do up the union. Turned on the unit and the gas actually lit off...
  17. You need one with a timed on cycle and temp off...

    You need one with a timed on cycle and temp off cycle. Shouldn't be hard to find cam-stat still makes them.
  18. Replies
    42
    Views
    4,600

    Screws

    Screws
  19. Replies
    4
    Views
    534

    A bad v-belt can cause that bouncing also, I do...

    A bad v-belt can cause that bouncing also, I do remember installing a reinforcing plate once upon a time.
  20. Replies
    69
    Views
    3,904

    Cause Trane started to do it, so now everyone is.

    Cause Trane started to do it, so now everyone is.
  21. Thread: Hot Gas Valve

    by Juleous
    Replies
    16
    Views
    1,013

    That is a bit of a trick question, there are...

    That is a bit of a trick question, there are lot's of reasons why that could be all would be correct but probably not what he is looking for. My best answer would be the type of defrost operation the...
  22. Replies
    40
    Views
    5,745

    Hard to see where all the pipe goes, I notice the...

    Hard to see where all the pipe goes, I notice the flex lines connected on the other end of the galvanized why? Weird for sure, also it looks like the drain is going uphill a bit there. That is one of...
  23. Replies
    12
    Views
    529

    TQ = Trade Qualification I thought you wanted...

    TQ = Trade Qualification

    I thought you wanted to be a refrigeration guy not a plunger guy. If you like to play with nasty toilets and such then be a plumber if you want a real trade then do the...
  24. Replies
    10
    Views
    1,019

    DIY answers not allowed on this forum.

    DIY answers not allowed on this forum.
  25. Replies
    17
    Views
    2,680

    I really like L-Series Tool Less test features,...

    I really like L-Series Tool Less test features, it sure makes them nice to service. In my opinion one of the better quality designs Lennox has done, one problem is the program settings in the boards...
Results 1 to 25 of 141
Page 1 of 6 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event