Search:

Type: Posts; User: allenwrench

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    820

    I just replaced a coil in a rheem unit yesterday,...

    I just replaced a coil in a rheem unit yesterday, put in an aluminum n coil by rheem. They are already distributing them in Ky.
  2. Replies
    50
    Views
    5,447

    Those things are scarce around these parts and...

    Those things are scarce around these parts and boy am I glad!!!! Been in the field 2years and only seen about seven of them. That was seven times I would rather forget about!!
  3. Replies
    4
    Views
    386

    I have also seen board not sending voltage to...

    I have also seen board not sending voltage to open solenoid as well. Hard to say without catching it , but could be a board problem
  4. Replies
    50
    Views
    5,447

    If I could get a copy of tha too that would be...

    If I could get a copy of tha too that would be great. We haveactually replaced 3 of these since I have been in this trade. Heavy piece of junk I will have to say!!
  5. Replies
    22
    Views
    3,029

    Where is the baffle again?

    Where is the baffle again?
  6. Replies
    29
    Views
    5,193

    He is in a tech to tech forum which means he...

    He is in a tech to tech forum which means he previously had to get his post to 15 before aloud to come here right? Give the new guys a break, I am still new myself and dont need constructive...
  7. Replies
    24
    Views
    3,491

    Also lp springs are purple and most of the time...

    Also lp springs are purple and most of the time ng springs are silver, this is just one way to maybe give you alittlle more confirmation.
  8. Replies
    23
    Views
    15,716

    lmbo!!!!

    lmbo!!!!
  9. Replies
    18
    Views
    2,239

    capacitor???

    Ok, I came up on a unit that had a dual cap 60/7.5 Do not have this on truck. was told to use bigger and not smaller when you dont have the right size. I put on a 60/10, will it be ok or should I...
  10. Replies
    7
    Views
    882

    I experienced this on two different compressors...

    I experienced this on two different compressors this summer, It was a squelling like a bad bearing in a fan motor but it was coming from the compressor. I did notice that when I pulled disconnect...
  11. Replies
    22
    Views
    2,770

    Absolutely, do it now rather than later. That...

    Absolutely, do it now rather than later. That moisture is in that filter drier and later on some tech is going to be replacing it due to it causing a restriction, so it may as well be cut out now and...
  12. Replies
    63
    Views
    6,513

    Guys I have to agree that there are many schools...

    Guys I have to agree that there are many schools that are only concerned with getting your money so their salaries can get paid. I graduated recently myself and have had my journeymans for a few...
  13. Replies
    27
    Views
    6,865

    The company I work for has experienced the same...

    The company I work for has experienced the same problems described with nordyne and no compensation. We have ate alot of freon cost too, needless to say we are not selling them anymore. We have made...
  14. I think a 50 is a bit large for a 1.5-2 ton. I...

    I think a 50 is a bit large for a 1.5-2 ton. I haved changed several 35uf caps on 3 ton units. I ran into the same situation myself this summer though, I put a 35/5 on it and so far so good.
  15. Replies
    19
    Views
    2,475

    Listen to baldloonie, he is telling you right,...

    Listen to baldloonie, he is telling you right, you will never flush a coil succesfully. I would be willing to say that if you try to flush the coil and change the txv, the compressor on that 410 unit...
  16. Replies
    69
    Views
    9,311

    I use a field piece sc76. It has the Amp clamp...

    I use a field piece sc76. It has the Amp clamp built in, has mfd and temp probe, it almost does everything. Why have two different meters; one for amping and one for voltage. Try this one I think you...
  17. Replies
    23
    Views
    2,157

    Are you saying you check all units with one set...

    Are you saying you check all units with one set of gauges? I have a set for both freons, 22 and 410
  18. Replies
    10
    Views
    1,669

    We use 7/8 on 5 ton unless the lineset is over 30...

    We use 7/8 on 5 ton unless the lineset is over 30 ft then you should use 1 1/8. The best answer is what ADILLION suggested, check the equipment std. The worst thing is getting called back because the...
  19. Replies
    102
    Views
    16,022

    Yea me too I'd take capacitor calls all day long...

    Yea me too I'd take capacitor calls all day long and we are getting alot too. I actually had to put on two hard starts in one day havent had that happen before.:whistle:
  20. Actually I have ran into this same problem myself...

    Actually I have ran into this same problem myself more than once. I had one in my own home and after the t-stat was about three years old, started noticing my unit would run more and more, performed...
  21. Replies
    7
    Views
    1,257

    They are 440 volt cap. Dont know where made, get...

    They are 440 volt cap. Dont know where made, get from local supplier.
  22. Replies
    7
    Views
    1,257

    bad capacitor

    Ok guys, I am pretty new in the trade, only had my journeymans for a few weeks and admit I still have a lot to learn. Wondering if someone could help me with this. I arrive to a call and the outside...
  23. Replies
    8
    Views
    844

    When all else fails always dye it. If it has a...

    When all else fails always dye it. If it has a leak it will show up with the light. if on a condensor throw black plastic over it and go to lookin.
  24. Replies
    8
    Views
    1,016

    I would have to agree with mcjo tech; it sounds...

    I would have to agree with mcjo tech; it sounds like a partial restriction and could use a condensor cleaning. Does it have filter drier on it. Check thelinetemp before the drier and after the drier
  25. Replies
    5
    Views
    893

    Thanks Guys I appreciate the help.

    Thanks Guys I appreciate the help.
  26. Replies
    5
    Views
    893

    Furnace control board

    First I am a new tech and my first post, so here it goes: I arrive to the call and the a/c is working and calling on and off by the t-stat but the indoor fan continues to run with the stat set on...
Results 1 to 26 of 41
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event