Search:

Type: Posts; User: KittenMittens

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    2,112

    I will refrain from insulating the headers as it...

    I will refrain from insulating the headers as it may become a problem in the future should it ever need service, This change out was a ASAP so the coating is scheduled to be perofrmed on the feild by...
  2. Replies
    21
    Views
    2,112

    well i'll have to figure something out to just...

    well i'll have to figure something out to just make them happy letting them know i'll personally go the extra mile to continue to get the jobs, even tho there is nothing wrong with the unit to begin...
  3. Replies
    21
    Views
    2,112

    319791 319791 no, we corrected that issue...

    319791

    319791

    no, we corrected that issue already... of course that unit sweats also out of the sides of the condenser/compressor compartment area... same issue same complaint

    To me it's not...
  4. Replies
    21
    Views
    2,112

    yes the unit is level, and yes in the exposed...

    yes the unit is level, and yes in the exposed area in the compressor area, on this model the evaporator is exposed as well for whatever reason (the headers)
  5. Replies
    21
    Views
    2,112

    My job is to try and make the customer satisfied...

    My job is to try and make the customer satisfied 100% with our installations and service, especially for the customers with multiple facillities. This units location is in a high salt enviorment as...
  6. Replies
    21
    Views
    2,112

    carrier 50tc - heavy condensation

    Good morning, I'm looking into a complaint of a customer recently about condensation coming off of the suction line and headers of the exposed evaporator on a carrier model 50TC-D12A2B5-0A0A0 10 ton...
  7. Completed - 4 guys and some pipe and pvc, may...

    Completed - 4 guys and some pipe and pvc, may look into a gantry crane from sunbelt next time
  8. we may look into purchasing one in the near...

    we may look into purchasing one in the near future, as i've seen the videos and think that this equipment could be very benificial. Any recommendations on the type to buy... I see they are made of...
  9. B**** cranes was priced at the most reasonable...

    B**** cranes was priced at the most reasonable rate in the area (4 hour work minimum 2 hours for the travel to job to portal) no additional fees. our regular crane service we use did not have the...
  10. 318301 318311 there you go,

    318301
    318311

    there you go,
  11. Wrong sized curb adapter.... Need to salvage this job ... Help

    Any advice or expertise is greatly appreciated; I have found myself in a bad situation and am trying to minimize the damage as much as possible. I had sold the bid to change out a 10 ton RTU that was...
  12. According to the installation manual there is a "...

    According to the installation manual there is a " through the base " option in which it comes with a slightly raised peice with stainless steel connections. I will for future installations quote and...
  13. Package RTU ... Complaint from customer...

    This is a facilities director at a health care facility we've done a installation on where we had to replace the system there previous system due to the bottom of the unit rusting out from being...
  14. Tempstar 3 ton - blower hub grinding?

    I've never had to replace a blower hub/wheel other than one that was coming apart visually or the fins were damaged or just excessive build up I plain rather replace than try and clean - however the...
  15. Replies
    1
    Views
    650

    resolved - they havent made that controller in...

    resolved - they havent made that controller in six years, bypassed - frame heaters run continuos.
  16. Replies
    1
    Views
    650

    XS Energy optimizer?

    I am under the impression this has to do with the frame heaters for a glass door line up - the ones in mention in particular are part of a anthonys glass door line up ), they are having a issue...
  17. Replies
    14
    Views
    1,859

    Thank you for everyones inputs, probe was jacked ...

    Thank you for everyones inputs, probe was jacked putting it into harvest way to early and the dump valve was leaking
  18. Replies
    14
    Views
    1,859

    the sump water temperture needs to be at 32...

    the sump water temperture needs to be at 32 degrees dosent it? so the continual slow drain and add of new make up water that is warmer will delay ice correct?

    it took 15-20 minuets for it to make...
  19. Replies
    14
    Views
    1,859

    came back in the morning noticed it was making...

    came back in the morning noticed it was making ice but in super thick sheets, ran it in another clean cycle and adjusted the thickness screw, seems to be working now still takes a pretty long time to...
  20. Replies
    14
    Views
    1,859

    The same day I was there it had been taken apart...

    The same day I was there it had been taken apart and cleaned, hours prior in the morning, i arrived in the afternoon from what i could tell the filters were replaced a few days ago aswell and from...
  21. Replies
    14
    Views
    1,859

    Manitowoc S-Series 1800 no ice

    New to ice machines, only had a breif time to look over the system will be going back tomorrow and have some questions on why this machine will not make any ice

    some info: had 5 degrees of...
  22. Replies
    9
    Views
    1,481

    Service experts?

    Has anyone that has worked for them or has insight on what to expect? I know they are a type of franchise so it could be worse or better depending on the location you’re working out of, I did my...
  23. Replies
    17
    Views
    2,101

    Thank you for all your inputs, so would it...

    Thank you for all your inputs, so would it benefit me to drop the objective all together?

    Would that alone keep you from interviewing me for lets say a standard tech/installer position in a larger...
  24. Replies
    17
    Views
    2,101

    Inputs on my résumé ?

    Any comments at all would help me out thanks.
Results 1 to 24 of 24
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event