Search:

Type: Posts; User: tegger

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: PMI Screen

    by tegger
    Replies
    4
    Views
    613

    re:

    Your correct. Our PC runs 24/7. We do reboot it about once a month due to the total physical memory building up.:patriot:
  2. Thread: PMI Screen

    by tegger
    Replies
    4
    Views
    613

    Re:

    After doing some 'confriguration of controller' and UNT's, upload/downloads. I rebooted our PC for the Metasys program and we are "now seeing the values change" on the screen for the AHU's, heating...
  3. Replies
    15
    Views
    1,371

    re:

    Cal1, our OA sensor Nickel probe is outside our wall into a parking ramp which is separated by 3"gap from our building block wall. It is in a conduit rectangle box connected to a 2x3 splice box. It...
  4. Thread: PMI Screen

    by tegger
    Replies
    4
    Views
    613

    PMI Screen

    Does any one know why my PMI screen on the Network Map when your in/on the AHU's screens doesn't want to "refresh itself" any more? All the CFM's or VFD's signals are not refreshing before your eyes...
  5. Replies
    15
    Views
    1,371

    re:

    We did find a spare one that we had on hand. I did remove the original one and ohm it out using a cup of water and using my portable thermostat to get the water to 70 degree. The ohm reading was...
  6. Thread: Mixed Air Temp

    by tegger
    Replies
    16
    Views
    1,705

    No, I have a new one on order. Then we will...

    No, I have a new one on order. Then we will change it out and see if it is the sensor. Just trying to find more info if anyone else has had this problem, Thanks
  7. Thread: Mixed Air Temp

    by tegger
    Replies
    16
    Views
    1,705

    re:

    No, the NCM 350 is through our DDC to the air handlers. We thought about switching the sensor the across coil face with another one which my guy said is about 20' long, to see if it does the same.
  8. Thread: Mixed Air Temp

    by tegger
    Replies
    16
    Views
    1,705

    Mixed Air Temp

    We have an issue with 1 of 4 AHU's mixed air temp. reading. It fluctuates about 8-10 degree in about 1 hr., which cause the relief damper to fluctuate open/close and the VFD to decrease/increase in...
  9. Replies
    15
    Views
    1,371

    I have a TE-6000-1 OA temp sensor that is reading...

    I have a TE-6000-1 OA temp sensor that is reading 18-20 degree higher then what the actual temp. is. How do I calibrate it through the DX-9100? What do I look for when I connect to the DX?
  10. Replies
    88
    Views
    11,628

    I have one NCM 350 PMI. I just got a error...

    I have one NCM 350 PMI. I just got a error message saying' cannot refresh vav window'. Is there something I can do about this? version 12.04
  11. Replies
    4
    Views
    526

    re:

    Were would it be listed in the GPL? Under what block? Unocc. Cooling? Or under the AHU's call for cooling block?

    I took some pics of the PC screen and I will figure out how to send them to you...
  12. Replies
    6
    Views
    546

    re:DX-9100 download

    I solve the problem with this issue by downloading the DOX5 file which rebooted the XT modules, which started all the equipment on the DX-9100, for thou of you who might run into this problem!:D
  13. Replies
    4
    Views
    526

    Metasys 12.04 PMI/Chiller Question

    We are operating JCI PMI version 12.04 BAS. We have a chiller that interfaces through a MicroTech to talk to Metasys. We have a DX-9100 for commuincation for cooling pumps, tower, chill pumps etc....
  14. Replies
    13
    Views
    1,481

    re:DX-9100 download

    I have my laptop connected to our DX and I want to download a XT module to re-boot it with a backup copy I downloaded from my PC. What is the simpleless steps to use? Thanks!
  15. Replies
    6
    Views
    546

    re:

    LETS BE/ACT PROFESSIONAL!!!!!!!!!!
  16. Replies
    6
    Views
    546

    re:reaper

    Thanks Reaper, I forgot to mention that it was on the DX-9100 for our chiller and heating loop. I notice the XT is flashing on the DX. I think it refer to one of the extension modules which Im trying...
  17. Replies
    6
    Views
    546

    XT#8 System Alarm

    I have an alarm today on my PMI Network Map showing red on the NC251-HW alarm. It happen to be raining outside and some thunder I was told, maybe a brown out. I'm trying to locate the problem but...
  18. Replies
    24
    Views
    2,484

    re:

    De nada
  19. Replies
    24
    Views
    2,484

    re:

    You are correct! I use a couple of different vendors that can repair older JCI components at a fractual cost compared to JCI. We are creating a CIP for 5 yrs. to upgrade every thing too current...
  20. Replies
    24
    Views
    2,484

    re:

    http://cgproducts.johnsoncontrols.com/default.aspx?main.aspx&2
  21. Thread: PMI/NC350

    by tegger
    Replies
    7
    Views
    588

    re:

    No we don't. I'm looking for a spare one base on the quote/price for a used one.
  22. Thread: PMI/NC350

    by tegger
    Replies
    7
    Views
    588

    Re:

    Can you verify what the pros or cons or benefits would be to go on a ADX server when we are currently running on a stand alone PC with mirror drives, WinXP,2.0 GB memory, GPL/PMI rev. 12.04 BAS with...
  23. We use 1- DX-9100 for our absorption chiller and...

    We use 1- DX-9100 for our absorption chiller and our hot water loop.
  24. Thread: PMI/NC350

    by tegger
    Replies
    7
    Views
    588

    re:

    Thanks
  25. Thread: PMI/NC350

    by tegger
    Replies
    7
    Views
    588

    Update, the software version we are using is...

    Update, the software version we are using is 12.04 for our NC350 with 4-DCM'S.
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event