Search:

Type: Posts; User: picnik

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Can't see your email in your profile. I have the...

    Can't see your email in your profile. I have the V3 SDU directory which has all the files you want. Email me and I'll send them back to you.

    I wish you luck in your project. I had a similar...
  2. Replies
    8
    Views
    562

    Do you recon those floor plans were done using...

    Do you recon those floor plans were done using ASCII characters. Did a few graphics back in the day doing that.
  3. Replies
    1
    Views
    224

    What help do you need?

    What help do you need?
  4. Replies
    3
    Views
    635

    The common alarm block allows the acknowedgement...

    The common alarm block allows the acknowedgement and resetting of all alarms in the current chart and all charts below by connecting to the relevant pins to do the acknowledge or reset.

    In...
  5. Replies
    6
    Views
    1,012

    You need one big DIEPT file. Its basically one...

    You need one big DIEPT file. Its basically one file per site. You cant have seperate ones for each controller.
  6. Could be. do they have a part number on them?

    Could be. do they have a part number on them?
  7. If your using a T1 sensor (FR-T1) then the table...

    If your using a T1 sensor (FR-T1) then the table below is right. The new type of sensor you have been sent might be a Ni1000 sensor (QAA24?) which are 0°C at 1000 Ohms. You can change from old to new...
  8. Replies
    2
    Views
    287

    we tend to use these guys. ...

    we tend to use these guys.

    http://www.synapsys-solutions.com/

    Seem to do a pretty good job
  9. Replies
    4
    Views
    572

    The TONN (basically a trend badged tridium...

    The TONN (basically a trend badged tridium controller) would probably take in the LON from the TAC. But I'll say that they're opening themselves up to a whole load of issues. To modify any of the TAC...
  10. Thread: Staefa Controls

    by picnik
    Replies
    16
    Views
    2,445

    I can send you a scanned in staefa service manual...

    I can send you a scanned in staefa service manual that has all that kit except the R.U22 but its 12Mb. Stick your email address in your profile and I can send it later today.
  11. Replies
    40
    Views
    4,971

    OK, so updated my java to 7 (Version 6 Build 41)...

    OK, so updated my java to 7 (Version 6 Build 41) and all seems to work fine now. Of course some stuff not implemented but as a start pretty good. Talks fine to my delta DSC1616E controller anyway. My...
  12. Replies
    40
    Views
    4,971

    Looks like a great idea. What java version do I...

    Looks like a great idea. What java version do I need as I get class version errors when I try and run

    java.lang.UnsupportedClassVersionError: Bad version number in .class file
  13. Thread: Siemens PXC3...

    by picnik
    Replies
    5
    Views
    844

    Sorry, was getting my part numbers mixed up. I...

    Sorry, was getting my part numbers mixed up. I stated PXC3.L but I was actually talking about a PXG3.L

    The device you are talking about is part of their Total Room Automation range and I believe...
  14. Thread: Siemens PXC3...

    by picnik
    Replies
    5
    Views
    844

    Theres a number of flavours of PXC3's, there the...

    Theres a number of flavours of PXC3's, there the PXC3.L which is a BACNet/LON to BACNet/UDP/IP router, the PXC3.M which is the same as PXC3.L but with added MS/TP connections, and I think there is a...
  15. Thread: Siemens PXC3...

    by picnik
    Replies
    5
    Views
    844

    By Schedule do you mean install/configure and...

    By Schedule do you mean install/configure and that you cant find it as a device in the drop down menu?

    I believe you need XWorks V5. They also have a stand alone program to set it up as well but...
  16. Replies
    5
    Views
    930

    sent a new link, but check your spam folder

    sent a new link, but check your spam folder
  17. Replies
    5
    Views
    930

    OK, but best remove your email from the thread....

    OK, but best remove your email from the thread. Should go in your profile...
  18. Replies
    5
    Views
    930

    drop me an email and I'll reply with the files. ...

    drop me an email and I'll reply with the files.

    Is the tool you're using the new one or the old one? the new tool works best if the firmware files are saved in a certain file structure. Its a big...
  19. Replies
    6
    Views
    904

    here's a screen shot of the settings a colleage...

    here's a screen shot of the settings a colleage has set to get his NIC709-USB100 working with XWorks

    347391
  20. Thread: Old Staefa

    by picnik
    Replies
    89
    Views
    11,935

    You'd need to put your email address in your...

    You'd need to put your email address in your profile if you want anyone to help you on this I think.

    Also, have you tried contacting your local Staefa branch?
  21. Replies
    6
    Views
    904

    I can confirm this device does work fine. we have...

    I can confirm this device does work fine. we have a few people using them in the office. you need to go into advanced settings and select legacy mode. also a good idea to run it as a service
  22. Replies
    6
    Views
    904

    Have you ever been able to connect with this...

    Have you ever been able to connect with this interface to other PXC's or is this the first time you've tried it?

    I think I tried one of these devices previously with XWorks 2.37 and it didn't...
  23. Replies
    3
    Views
    895

    I know what you mean. I installed some wireless...

    I know what you mean. I installed some wireless sensors a while back as drilling the grade 1 listed building was out of the question. But the 2 foot think walls in places meant reception was an...
  24. Replies
    3
    Views
    895

    Wireless MBus Gateway

    Has anyone connected wireless MBus devices to a BMS? I have a solution for wired MBus but struggling a bit with wireless.

    What devices have you used to convert it into a protocol that your BMS can...
  25. Replies
    4
    Views
    1,183

    That would be a great application. Not sure about...

    That would be a great application. Not sure about setting the standard weekly schedule through it but I could see exceptions and calander events being integrated quite well.
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event