I stayed in Garland it was great and I took the family they enjoyed themselves too.
I think they have a deal with Entech for a reduced rate too.
From UA 469 and a CM too :D
Type: Posts; User: colddr469
I stayed in Garland it was great and I took the family they enjoyed themselves too.
I think they have a deal with Entech for a reduced rate too.
From UA 469 and a CM too :D
I don't know what your Peak demand rates are in Texas but that will determine your payback the XR was also sold as an XRV and that would probably be your most cost effective upgrade with the quickest...
It was the remote temp reset was enabled but it had no 4 - 20 milliamp signal
so it saw a value less than 0 and thus the sensor failure. Thanks for your help it got me going in the right direction....
the remote signals are not enabled
I have swapped out the processor board, I/O board and MP 3200 with used
boards we had at the shop and still get the 64 error code when I disconect the ESP I still get the code on the MP3200. so I...
Esp Ii
I have a 19 DK that alarms on 64, but only in remote on the MP 3200 when in local all is good has anybody seen this before? I also have 38 steps on the control test instead of 34 or 44. and last but...
Ther is no problem that can't be engineered to death the biggest problem is 110 degree outside air @ 100% is still 110 degrees so to get 55 degree supply air is a hard sell for me but the V E segment...
Do the lag compressor check valves slap when when they stage up?
Its the only way I can tell if the lag compressors are starting on the Mcquay machines. I'm wondering if the larger diameter valves...
Blackbeard Great info thanks for the 411 on the flow switches www.ifmefector.com/ifmus/web/dsfs!U40100.html
These are the s... just ordered one for a 19DM in the basement of a 30 story high rise...
I had a 50TJQ007 a few years ago that would leak through the base rail and had to take it down to the base and gasket everthing, these where the same units with the 6 ton scrolls that would break the...
Pid made easy
The way it was described to me was in an analogy, here goes:
Picture a man driving a car a standard ems is the cruise control all is fine on a straight road with no deviations but when there is a...
RSES Members
Are ther any other RSES members out there?:cool:
Entech
Has anybody out there been to an Entech school? If so how would you rate them compared to the manufacturers factory training? I'm wondering if there training would be better for the buck.
Colddr
Get Comfortview
With out the software it gets alot harder to get the bugs out plus you can keep a copy after the on site people adjust in new problems load on to a laptop but you'll need a serial port ( kind of a...
Pid made easy
The way it was described to me was in an analogy, here goes:
Picture a man driving a car a standard ems is the cruise control all is fine on a straight road with no deviations but when there is a...
Whats the OA ?
Check the outside air dampers and the is the fan running continuous? there are some field upgrades that can be done. Also what boad do you have 1.6 or 2.0 the latest is far less problems so far but...
I did the Air Force and am in the UA now and would recomend the UA as the way to go the pay is far better than anything else out there plus Medical. dental. vision, Retirement. Even as an apprentice...
Its my understanding that these turbo cor compressors look for lift differential 1st & formost so when your upside down on your tower and building loop it will stop loading (from what I was told...
47" is the magic number
:) 47" is the cut off for molded belts if it is less than 47" it is a spliced belt made from a straight corded belt with a splice that wants to find a way to straighten out again (like everyone elses...
Quote:
Originally Posted by NYChvacTech
ha's and pcv's are sidewinders. The motor is perpendicular to the shells. benchgrinders have a double ended motor. one wheel on each side.
Not...
Molded belts
If your belt size is 47" or above these are the best belts out there. More horsepower and smooth face Not the sawtoothed pulley eaters like X series belts. for large horsepower multi-belt...
Local 469:rolleyes:
Local 469:rolleyes:
It's the future Boyz
These things are great the best thing since sliced bread (outside of some software glitches they run so quiet you have to put a hand on the discharge line to tell which compressor is running they...
refer teacher would be proud
About 15 -20 lbs every 6 or seven hours around a 30 lb tank got over 1 gallon of water out with the vacuum between 1750 and 2000 microns.:cool:
Old School!
Made a quick one today after going through lots of oil over the week-end and still only down to 5000 microns on Tuesday evening. Used 2 30# recovery
tanks and a couple steele 10 gallon trash cans...
Looks to me like its under 5 -7 amps its when the...
Looks to me like its under 5 -7 amps its when the amp draw is in that 5-7 range you need to start looking for bearing problems even referteachers newly rebiult trane has alittle over 1 amp. I'm sure...
Oil line amps
Did you check the amp draw on the oil return line appparently amp draws over 5 amps on the copper oil return line can be an early indicator of beariing wear. I'm interested to see what your amp draw...